|
|
Número de pieza | HYB18L512320BF-7.5 | |
Descripción | DRAMs for Mobile Applications 512-Mbit SDR Mobile-RAM | |
Fabricantes | Qimonda AG | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de HYB18L512320BF-7.5 (archivo pdf) en la parte inferior de esta página. Total 23 Páginas | ||
No Preview Available ! HYB18L512320BF-7.5
HYE18L512320BF-7.5
DRAMs for Mobile Applications
512-Mbit SDR Mobile-RAM
August 2007
www.DataSheet4U.com
Internet Data Sheet
Rev.1.22
1 page 1.2
Pin Configuration
Internet Data Sheet
www.DataSheet4U.com
HY[B/E]18L512320BF-7.5
512-Mbit Mobile-RAM
FIGURE 1
Standard Ballout 256-Mbit Mobile-RAM (Top View x32)
'4
'4
9664
9664
9''4
966
'4
9''4
'4
'4
'4
'40
966
9664
'4
'4
1&
$
$ $ $
$ $ $
&/. &.( $
'40 1&
9''4 '4
1&
966
9664
9664
'4
'4
'4
'4
9''4
'4
'4
'4
9664
966
$ 9'' '4 '4
% 9''4 9664 '4
& '4 '4 9''4
' '4 '4 9''4
( 1& '4 9664
) $ '40 9''
* $$3 $
$
+ 1& %$ $
- %$ &6 5$6
. &$6 :( '40
/ 9'' '4 9664
0 '4 '4 9''4
1 '4 '4 9''4
3 9''4 9664 '4
5 9'' '4 '4
Rev.1.22, 2007-08
03292006-D7GM-ZBSS
5
5 Page Internet Data Sheet
www.DataSheet4U.com
HY[B/E]18L512320BF-7.5
512-Mbit Mobile-RAM
10) May or may not be bank-specific; if multiple banks are to be precharged, each must be in a valid state for precharging.
11) Not bank-specific; BURST TERMINATE affects the most recent READ or WRITE burst, regardless of bank.
TABLE 8
Current State Bank n - Command to Bank m (different bank)
Current State CS RAS CAS WE Command / Action
Notes
Any
H X X X DESELECT (NOP / continue previous operation)
1)2)3)4)5)6)
L H H H NO OPERATION (NOP / continue previous operation)
1)2)3)4)5)6)
Idle X X X X Any command otherwise allowed to bank n
1)2)3)4)5)6)
Row Activating, L L H H ACTIVE (select and activate row)
Active, or
L H L H READ (select column and start READ burst)
Precharging L H L L WRITE (select column and start WRITE burst)
1)2)3)4)5)6)
1)2)3)4)5)6)7)
1)2)3)4)5)6)7)
L L H L PRECHARGE (deactivate row in bank or banks)
1)2)3)4)5)6)
Read (Auto- L L H H ACTIVE (select and activate row)
Precharge
Disabled)
L H L H READ (select column and start READ burst)
L H L L WRITE (select column and start WRITE burst)
1)2)3)4)5)6)
1)2)3)4)5)6)7)
1)2)3)4)5)6)7)8)
L L H L PRECHARGE (deactivate row in bank or banks)
1)2)3)4)5)6)
Write (Auto- L L H H ACTIVE (select and activate row)
Precharge
Disabled)
L H L H READ (select column and start READ burst)
L H L L WRITE (select column and start WRITE burst)
1)2)3)4)5)6)
1)2)3)4)5)6)7)
1)2)3)4)5)6)7)
L L H L PRECHARGE (deactivate row in bank or banks)
1)2)3)4)5)6)
Read(with Auto- L L H H ACTIVE (select and activate row)
Precharge)
1)2)3)4)5)6)
L H L H READ (select column and start READ burst)
1)2)3)4)5)6)7)9)
L H L L WRITE (select column and start WRITE burst)
1)2)3)4)5)6)7)8)9)
L L H L PRECHARGE (deactivate row in bank or banks)
1)2)3)4)5)6)
Write(with Auto- L L H H ACTIVE (select and activate row)
Precharge)
L H L H READ (select column and start READ burst)
1)2)3)4)5)6)
1)2)3)4)5)6)7)9)
L H L L WRITE (select column and start WRITE burst)
1)2)3)4)5)6)7)9)
L L H L PRECHARGE (deactivate row in bank or banks)
1)2)3)4)5)6)
1) This table applies when CKEn-1 was HIGH and CKEn is HIGH and after tRC has been met (if the previous state was Self Refresh).
2) This table describes alternate bank operation, except where noted, i.e., the current state is for bank n and the commands shown are those
allowed to be issued to bank m (assuming that bank m is in such a state that the given command is allowable). Exceptions are covered in
the notes below.
3) Current state definitions:Idle:The bank has been precharged, and tRP has been met.Row Active:A row in the bank has been activated, and
tRCD has been met. No data bursts/accesses and no register accesses are in progress.Read:A READ burst has been initiated, with Auto
Precharge disabled, and has not yet terminated orbeen terminated.Write:A WRITE burst has been initiated, with Auto Precharge disabled,
and has not yet terminated or been terminated.Read with AP Enabled:Starts with registration of a READ command with Auto Precharge
enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state.Write with AP Enabled:Starts with registration of a
WRITE command with Auto Precharge enabled and ends when tRP has been met. Once tRP is met, the bank is in the idle state.
4) AUTO REFRESH, SELF REFRESH and MODE REGISTER SET commands may only be issued when all banks are idle.
5) A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state only.
6) All states and sequences not shown are illegal or reserved.
7) READs or WRITEs listed in the Command/Action column include READs or WRITEs with Auto Precharge enabled and READs or WRITEs
with Auto Precharge disabled.
8) Requires appropriate DQM masking.
Rev.1.22, 2007-08
03292006-D7GM-ZBSS
11
11 Page |
Páginas | Total 23 Páginas | |
PDF Descargar | [ Datasheet HYB18L512320BF-7.5.PDF ] |
Número de pieza | Descripción | Fabricantes |
HYB18L512320BF-7.5 | DRAMs for Mobile Applications 512-Mbit SDR Mobile-RAM | Qimonda AG |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |