|
|
PDF HYMD264G726BLF4-J Data sheet ( Hoja de datos )
| Número de pieza | HYMD264G726BLF4-J | |
| Descripción | Registered DDR SDRAM DIMM | |
| Fabricantes | Hynix Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HYMD264G726BLF4-J (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
DESCRIPTION
w6w4wM.Daxta7Sh2eebt4iUt.csom
Registered DDR SDRAM DIMM
HYMD264G726B(L)F4-J
Preliminary
Hynix HYMD264G726B(L)F4-J series is registered 184-pin double data rate Synchronous DRAM Dual In-Line Memory
Modules (DIMMs) which are organized as 64Mx72 high-speed memory arrays. Hynix HYMD264G726B(L)F4-J series
consists of eighteen 64Mx4 DDR SDRAM in FBGA packages on a 184pin glass-epoxy substrate. Hynix
HYMD264G726B(L)F4-J series provide a high performance 8-byte interface in 5.25" width form factor of industry stan-
dard. It is suitable for easy interchange and addition.
Hynix HYMD264G726B(L)F4-J series is designed for high speed of up to 166MHz and offers fully synchronous opera-
tions referenced to both rising and falling edges of differential clock inputs. While all addresses and control inputs are
latched on the rising edges of the clock, Data, Data strobes and Write data masks inputs are sampled on both rising
and falling edges of it. The data paths are internally pipelined and 2-bit prefetched to achieve very high bandwidth. All
input and output voltage levels are compatible with SSTL_2. High speed frequencies, programmable latencies and
burst lengths allow variety of device operation in high performance memory system.
Hynix HYMD264G726B(L)F4-J series incorporates SPD(serial presence detect). Serial presence detect function is
implemented via a serial 2,048-bit EEPROM. The first 128 bytes of serial PD data are programmed by Hynix to identify
DIMM type, capacity and other the information of DIMM and the last 128 bytes are available to the customer.
FEATURES
• 512MB (64M x 72) Registered DDR DIMM based on • Fully differential clock operations (CK & /CK) with
64Mx4 DDR SDRAM
100MHz/125MHz/133MHz/166MHz
• JEDEC Standard 184-pin dual in-line memory mod-
ule (DIMM)
• Error Check Correction (ECC) Capability
• Programmable CAS Latency 2 / 2.5 supported
• Programmable Burst Length 2 / 4 / 8 with both
sequential and interleave mode
• Registered inputs with one-clock delay
• tRAS Lock-out function supported
• Phase-lock loop (PLL) clock driver to reduce loading • Internal four bank operations with single pulsed RAS
• 2.5V +/- 0.2V VDD and VDDQ Power supply
• Auto refresh and self refresh supported
• All inputs and outputs are compatible with SSTL_2
interface
• 8192 refresh cycles / 64ms
ORDERING INFORMATION
Part No.
HYMD264G726B(L)F4-J
Power Supply
VDD=2.5V
VDDQ=2.5V
Clock Frequency
166MHz (*DDR333)
Interface
Form Factor
SSTL_2
184pin Registered DIMM
5.25 x 1.125 x 0.15 inch
* JEDEC Defined Specifications compliant
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev. 0.1 / Mar. 2003
1
1 page  
www.DataSh
HYMD264G726B(L)F4-J
AC OPERATING TEST CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Parameter
Reference Voltage
Termination Voltage
AC Input High Level Voltage (VIH, min)
AC Input Low Level Voltage (VIL, max)
Input Timing Measurement Reference Level Voltage
Output Timing Measurement Reference Level Voltage
Input Signal maximum peak swing
Input minimum Signal Slew Rate
Termination Resistor (RT)
Series Resistor (RS)
Output Load Capacitance for Access Time Measurement (CL)
Value
VDDQ x 0.5
VDDQ x 0.5
VREF + 0.31
VREF - 0.31
VREF
VTT
1.5
1
50
25
30
Unit
V
V
V
V
V
V
V
V/ns
W
W
pF
Rev. 0.1 / Mar. 2003
5
5 Page 
www.DataSheet4U.com
HYMD264G726B(L)F4-J
10. tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL). tQHS consists of
tDQSQmax, the pulse width distortion of on-chip clock circuits, data pin to pin skew and output pattern effects and p-channel
to n-channel variation of the output drivers.
11. This derating table is used to increase tDS/tDH in case where the input slew-rate is below 0.5V/ns.
Input Setup / Hold Slew-rate Derating Table.
Input Setup / Hold Slew-rate
Delta tDS
Delta tDH
V/ns
ps ps
0.5 0 0
0.4 +75 +75
0.3
+150
+150
12. I/O Setup/Hold Plateau Derating. This derating table is used to increase tDS/tDH in case where the input level is flat below
VREF +/-310mV for a duration of up to 2ns.
I/O Input Level
Delta tDS
Delta tDH
mV ps ps
+280
+50 +50
13. I/O Setup/Hold Delta Inverse Slew Rate Derating. This derating table is used to increase tDS/tDH in case where the DQ and
DQS slew rates differ. The Delta Inverse Slew Rate is calculated as (1/SlewRate1)-(1/SlewRate2). For example, if slew rate
1=0.5V/ns and Slew Rate2 = 0.4V/n then the Delta Inverse Slew Rate = -0.5ns/V.
(1/SlewRate1)-(1/SlewRate2)
Delta tDS
Delta tDH
ns/V
ps ps
0 00
+/-0.25
+50 +50
+/- 0.5
+100
+100
14. DQS, DM and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times.
Signal transi tions through the DC region must be monotonic.
15. tDAL = (tDPL / tCK ) + (tRP / tCK ). For each of the terms above, if not already an integer, round to the next highest integer.
tCK is equal to the actual system clock cycle time.
Example: For DDR266B at CL=2.5 and tCK = 7.5 ns,
tDAL = (15 ns / 7.5 ns) + (20 ns / 7.5 ns) = (2.00) + (2.67)
Round up each non-integer to the next highest integer: = (2) + (3), tDAL = 5 clock
16. For the parts which do not has internal RAS lockout circuit, Active to Read with Auto precharge delay should be
tRAS - BL/2 x tCK.
17. tHZ and tLZ transitions occur in the same access time windows as valid data trasitions. These parameters are not referenced
to a specific voltage level but specify when the device output is no longer driving (HZ), or begins driving (LZ).
Rev. 0.1 / Mar. 2003
11
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet HYMD264G726BLF4-J.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HYMD264G726BLF4-J | Registered DDR SDRAM DIMM | Hynix Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |