|
|
PDF FAN3268 Data sheet ( Hoja de datos )
| Número de pieza | FAN3268 | |
| Descripción | 2A Low-Voltage PMOS-NMOS Bridge Driver | |
| Fabricantes | Fairchild Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de FAN3268 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
February 2009
FAN3268
2A Low-Voltage PMOS-NMOS Bridge Driver
Features
4.5V to 18V Operating Range
Drives High-Side PMOS and Low-Side NMOS in
Motor Control or Buck Step-down Applications
Inverting Channel B Biases High-Side PMOS
Device Off (with internal 100kΩ Resistor) when
VDD is below UVLO Threshold
TTL Input Thresholds
2.4A Sink / 1.6A Source at VOUT=6V
Internal Resistors Turn Driver Off If No Inputs
MillerDrive™ Technology
8-Lead SOIC Package
Rated from –40°C to +125°C Ambient
Applications
Motor Control with PMOS / NMOS Half-Bridge
Configuration
Buck Converters with High-Side PMOS Device;
100% Duty Cycle Operation Possible
www.DataSheet4LUo.cgoicm-Controlled Load Circuits with High-Side
PMOS Switch
Description
The FAN3268 dual 2A gate driver is optimized to drive a
high-side P-channel MOSFET and a low-side N-channel
MOSFET in motor control applications operating from a
voltage rail up to 18V. The driver has TTL input
thresholds and provides buffer and level translation
functions from logic inputs. Internal circuitry provides an
under-voltage lockout function that prevents the output
switching devices from operating if the VDD supply
voltage is below the operating level. Internal 100kΩ
resistors bias the non-inverting output low and the
inverting output to VDD to keep the external MOSFETs
off during startup intervals when logic control signals
may not be present.
The FAN3268 driver incorporates MillerDrive™
architecture for the final output stage. This bipolar-
MOSFET combination provides high current during the
Miller plateau stage of the MOSFET turn-on / turn-off
process to minimize switching loss, while providing rail-
to-rail voltage swing and reverse current capability.
The FAN3268 has two independent enable pins that
default to on if not connected. If the enable pin for non-
inverting channel A is pulled low, OUTA is forced low; if
the enable pin for inverting channel B is pulled low,
OUTB is forced high. If an input is left unconnected,
internal resistors bias the inputs such that the external
MOSFETs are off.
Figure 1. Typical Motor Drive Application
© 2009 Fairchild Semiconductor Corporation
FAN3268 • Rev. 1.0.0
1
www.fairchildsemi.com
1 page  
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device
reliability. The absolute maximum ratings are stress ratings only.
Symbol
Parameter
VDD VDD to PGND
VEN ENA, ENB to GND
VIN INA, INB to GND
VOUT OUTA, OUTB to GND
TL Lead Soldering Temperature (10 Seconds)
TJ Junction Temperature
TSTG Storage Temperature
ESD
Electrostatic Discharge
Protection Level
Human Body Model, JEDEC JESD22-A114
Charged Device Model, JEDEC JESD22-C101
Min.
Max. Unit
-0.3
20.0
V
GND - 0.3 VDD + 0.3
GND - 0.3 VDD + 0.3
V
V
GND - 0.3 VDD + 0.3
+260
V
ºC
-55
+150
ºC
-65
+150
ºC
3.5 kV
2 kV
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to Absolute Maximum Ratings.
Symbol
Parameter
VDD Supply Voltage Range
VEN Enable Voltage (ENA, ENB)
VIN Input Voltage (INA, INB)
TA Operating Ambient Temperature
www.DataSheet4U.com
Min.
4.5
0
0
-40
Max.
18.0
VDD
VDD
+125
Unit
V
V
V
ºC
Electrical Characteristics
Unless otherwise noted, VDD=12V and TJ=-40°C to +125°C. Currents are defined as positive into the device and
negative out of the device.
Symbol
Parameter
SUPPLY
VDD Operating Range
IDD
Supply Current Inputs / EN Not
Connected
VON
VOFF
INPUT(8)
Turn-On Voltage
Turn-Off Voltage
VIL INx Logic Low Threshold
VIH INx Logic High Threshold
VHYS Logic Hysteresis Voltage
Conditions
Min. Typ. Max. Unit
4.5 18.0 V
0.75 1.20 mA
INA=ENA=VDD, INB=ENB=0V
INA=ENA=VDD, INB=ENB=0V
3.5
3.3
3.9 4.3
3.7 4.1
V
V
0.8 1.2
V
1.6 2.0
V
0.2 0.4 0.8 V
© 2009 Fairchild Semiconductor Corporation
FAN3268 • Rev. 1.0.0
5
www.fairchildsemi.com
5 Page 
Applications Information
Input Thresholds
The FAN3268 driver has TTL input thresholds and
provides buffer and level translation functions from logic
inputs. The input thresholds meet industry-standard
TTL-logic thresholds, independent of the VDD voltage,
and there is a hysteresis voltage of approximately 0.4V.
These levels permit the inputs to be driven from a range
of input logic signal levels for which a voltage over 2V is
considered logic high. The driving signal for the TTL
inputs should have fast rising and falling edges with a
slew rate of 6V/µs or faster, so a rise time from 0 to
3.3V should be 550ns or less. With reduced slew rate,
circuit noise could cause the driver input voltage to
exceed the hysteresis voltage and retrigger the driver
input, causing erratic operation.
Static Supply Current
In the IDD (static) typical performance characteristics
(see Figure 6), the curve is produced with all inputs /
enables floating (OUT is low) and indicates the lowest
static IDD current for the tested configuration. For other
states, additional current flows through the 100kΩ
resistors on the inputs and outputs shown in the block
diagram (see Figure 3). In these cases, the actual static
IDD current is the value obtained from the curves plus
this additional current.
MillerDrive™ Gate Drive Technology
FAN3268 gate drivers incorporate the MillerDrive™
architecture shown in 0. For the output stage, a
combination of bipolar and MOS devices provide large
currents over a wide range of supply voltage and
temperature variations. The bipolar devices carry the
bulk of the current as OUT swings between one and two
thirds VDD and the MOS devices pull the output to the
www.DataShheigeth4Uo.rcloomw rail.
The purpose of the MillerDrive™ architecture is to
speed up switching by providing high current during the
Miller plateau region when the gate-drain capacitance of
the MOSFET is being charged or discharged as part of
the turn-on / turn-off process.
For applications with zero voltage switching during the
MOSFET turn-on or turn-off interval, the driver supplies
high peak current for fast switching even though the
Miller plateau is not present. This situation often occurs
in synchronous rectifier applications because the body
diode is generally conducting before the MOSFET is
switched on.
The output pin slew rate is determined by VDD voltage
and the load on the output. It is not user adjustable, but
a series resistor can be added if a slower rise or fall
time at the MOSFET gate is needed.
Figure 27. MillerDrive™ Output Architecture
Under-Voltage Lockout
Internal circuitry provides an under-voltage lockout
function that prevents the output switching devices from
operating if the VDD supply voltage is below the
operating level. When VDD is rising, but below the 3.9V
operational level, internal 100kΩ resistors bias the non-
inverting output low and the inverting output to VDD to
keep the external MOSFETs off during startup intervals
when logic control signals may not be present. After the
part is active, the supply voltage must drop 0.2V before
the part shuts down. This hysteresis helps prevent
chatter when low VDD supply voltages have noise from
the power switching.
VDD Bypass Capacitor Guidelines
To enable this IC to turn a device on quickly, a local
high-frequency bypass capacitor CBYP with low ESR and
ESL should be connected between the VDD and GND
pins with minimal trace length. This capacitor is in
addition to bulk electrolytic capacitance of 10µF to 47µF
commonly found on driver and controller bias circuits.
A typical criterion for choosing the value of CBYP is to
keep the ripple voltage on the VDD supply to ≤5%. This
is often achieved with a value ≥20 times the equivalent
load capacitance CEQV, defined here as QGATE/VDD.
Ceramic capacitors of 0.1µF to 1µF or larger are
common choices, as are dielectrics, such as X5R and
X7R, with good temperature characteristics and high
pulse current capability.
If circuit noise affects normal operation, the value of
CBYP may be increased to 50-100 times the CEQV or
CBYP may be split into two capacitors. One should be a
larger value, based on equivalent load capacitance, and
the other a smaller value, such as 1-10nF mounted
closest to the VDD and GND pins to carry the higher
frequency components of the current pulses. The
bypass capacitor must provide the pulsed current from
both of the driver channels and, if the drivers are
switching simultaneously, the combined peak current
sourced from the CBYP would be twice as large as when
a single channel is switching.
© 2009 Fairchild Semiconductor Corporation
FAN3268 • Rev. 1.0.0
11
www.fairchildsemi.com
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet FAN3268.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| FAN3268 | 2A Low-Voltage PMOS-NMOS Bridge Driver | Fairchild Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |