DS25CP114 Datasheet PDF - National Semiconductor
| Part Number | DS25CP114 | |
| Description | (DS25CP104A / DS25CP114) 3.125 Gbps 4x4 LVDS Crosspoint Switch | |
| Manufacturers | National Semiconductor | |
| Logo |  |
|
|
There is a preview and DS25CP114 download ( pdf file ) link at the bottom of this page. Total 28 Pages | ||
Preview 1 page No Preview Available !
www.DataSheet4U.com
DS25CP104A / DS25CP114
May 13, 2009
3.125 Gbps 4x4 LVDS Crosspoint Switch with Transmit
Pre-Emphasis and Receive Equalization
General Description
The DS25CP104A and DS25CP114 are 3.125 Gbps 4x4
LVDS crosspoint switches optimized for high-speed signal
routing and switching over lossy FR-4 printed circuit board
backplanes and balanced cables. Fully differential signal
paths ensure exceptional signal integrity and noise immunity.
The non-blocking architecture allows connections of any input
to any output or outputs. The switch configuration can be ac-
complished via external pins or the System Management Bus
(SMBus) interface.
The DS25CP104A and DS25CP114 feature four levels (Off,
Low, Medium, High) of transmit pre-emphasis (PE) and four
levels (Off, Low, Medium, High) of receive equalization (EQ)
settable via the SMBus interface. Off and Medium PE levels
and Off and Low EQ levels are settable with the external pins.
In addition, the SMBus circuitry enables the loss of signal
(LOS) monitors that can inform a system of the presence of
an open inputs condition (e.g. disconnected cable).
Wide input common mode range allows the switch to accept
signals with LVDS, CML and LVPECL levels; the output levels
are LVDS. A very small package footprint requires a minimal
space on the board while the flow-through pinout allows easy
board layout. On the DS25CP104A each differential input and
output is internally terminated with a 100Ω resistor to lower
return losses, reduce component count and further minimize
board space. For added design flexibility the 100Ω input ter-
minations on the DS25CP114 have been eliminated. This
enables a designer to build custom crosspoint configurations
and distribution circuits that require a limited multidrop sig-
naling topology.
Features
■ DC - 3.125 Gbps low jitter, low skew, low power operation
■ Pin and SMBus configurable, fully differential, non-
blocking architecture
■ Pin (two levels) and SMBus (four levels) selectable pre-
emphasis and equalization eliminate ISI jitter
■ Wide Input Common Mode Range enables easy interface
to CML and LVPECL drivers
■ LOS circuitry detects open inputs fault condition
■ On-chip 100Ω input and output termination minimizes
insertion and return losses, reduces component count and
minimizes board space. The DS25CP114 eliminates the
on-chip input termination for added design flexibility.
■ 8 kV ESD on LVDS I/O pins protects adjoining
components
■ Small 6 mm x 6 mm LLP-40 space saving package
Applications
■ SD/HD/3G HD SDI Routers
■ OC-48 / STM-16
■ InfiniBand and FireWire
Typical Application
© 2009 National Semiconductor Corporation 300736
30073603
www.national.com
|
| |
 
wwPwi.nDatDaSehesect4Uri.cpomtions
Pin Name
IN0+, IN0- ,
IN1+, IN1-,
IN2+, IN2-,
IN3+, IN3-
OUT0+, OUT0-,
OUT1+, OUT1-,
OUT2+, OUT2-,
OUT3+, OUT3-
EQ0, EQ1,
EQ2, EQ3
PE0, PE1,
PE2, PE3
EN_smb
Pin
Number
1, 2,
4, 5,
6, 7,
9, 10
29, 28,
27, 26,
24, 23,
22, 21
40, 39,
11, 12
31, 20,
19, 18
17
I/O, Type
I, LVDS
O, LVDS
I, LVCMOS
I, LVCMOS
I, LVCMOS
S00/SCL
S01/SDA
S10/ADDR0,
S11/ADDR1
S20/ADDR2,
S21/ADDR3
S30, S31
37 I, LVCMOS
36 I/O, LVCMOS
35, I, LVCMOS
34
33, I, LVCMOS
32
13, 14 I, LVCMOS
PWDN
38 I, LVCMOS
VDD
GND
3, 8, Power
15,25, 30
16, DAP Power
Pin Description
Inverting and non-inverting high speed LVDS input pins. These 4
input pairs have a 100 Ohm differential input termination on the
CP104A device. The CP114 eliminates the input termination for
added design flexibility.
Inverting and non-inverting high speed LVDS output pins. Each
output pair has an internal 100 Ohm termination to improve device
return loss characteristics.
Receive equalization level select pins. These pins are functional
regardless of the EN_smb pin state.
Transmit pre-emphasis level select pins. These pins are functional
regardless of the EN_smb pin state.
System Management Bus (SMBus) enable pin. The pin has an
internal pull down. When the pin is set to a [1], the device is in the
SMBus mode. All SMBus registers are reset when this pin is
toggled. There is a 20k pulldown device on this pin.
For EN_smb = [0], these pins select which LVDS input is routed
to the OUT0.
In the SMBus mode, when the EN_smb = [1], these pins are
SMBus clock input and data input pins respectively.
For EN_smb = [0], these pins select which LVDS input is routed
to the OUT1.
In the SMBus mode, when the EN_smb = [1], these pins are the
User-Set SMBus Slave Address inputs.
For EN_smb = [0], these pins select which LVDS input is routed
to the OUT2.
In the SMBus mode, when the EN_smb = H, these pins are the
User-Set SMBus Slave Address inputs.
For EN_smb = [0], these pins select which LVDS input is routed
to the OUT3.
In the SMBus mode, when the EN_smb = [1], these pins are non-
functional and should be tied to either logic H or L.
For EN_smb = [0], this is the power down pin. When the PWDN is
set to a [0], the device is in the power down mode. The SMBus
circuitry can still be accessed provided the EN_smb pin is set to a
[1].
In the SMBus mode, the device is powered up by either setting the
PWDN pin to [1] OR by writing a [1] to the Control Register D[7]
bit ( SoftPWDN). The device will be powered down by setting the
PWDN pin to [0] AND by writing a [0] to the Control Register D[7]
bit ( SoftPWDN).
Power supply pins.
Ground pin and a pad (DAP - die attach pad).
Note: Center DAP connection must be made to GND for optimum electrical and thermal performance.
5 www.national.com
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for DS25CP114 electronic component. |
| Information | Total 28 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ DS25CP114.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| DS25CP114 | The function is DS25CP104A/CP114 3.125 Gbps 4x4 LVDS Xpoint Sw w/Xmit Pre-Emp Receive Equal (Rev. C). Texas Instruments |  |
| DS25CP114 | The function is (DS25CP104A / DS25CP114) 3.125 Gbps 4x4 LVDS Crosspoint Switch. National Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
DS25
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||