|
|
PDF SD42511 Data sheet ( Hoja de datos )
| Número de pieza | SD42511 | |
| Descripción | 1A WHITE LED DRIVER | |
| Fabricantes | Silan | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de SD42511 (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
SD42511
1A WHITE LED DRIVER WITH PWM DIMMING CONTROLLER
DESCRIPTION
The SD42511 is a step-down PWM control LED driver with a built-in
internal power MOSFET. It achieves 1A continuous output current over
a wide input supply range. It provides thermal shutdown circuit, current
limiting circuit and PWM dimming circuit.
SD42511 adopts current mode control. Current mode operation
provides fast transient response and simple loop stabilization design.
SD42511 has high efficiency up to more than 90%, and has excellent
constant current characteristic when the input/output voltage changed,
with the excellent current accuracy within ±1%. With the high input
voltage of up to 25V and built-in slope compensation, it can drive 6
LEDs.
FEATURES
* Maximum 1A output current
* 0.25Ω built-in power MOSFET
* PWM dimming function
* 280KHz fixed frequency
* Excellent constant current accuracy ±1%
* High efficiency up to 90%
* Thermal shutdown
* Cycle-by-cycle over current protection
* 6-25V input voltage range
* Drive LED string
ORDERING INFORMATION
Device
SD42511
Package
SOP-8-225-1.27
APPLICATIONS
* Power LED driver
BLOCK DIAGRAM
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http://www.silan.com.cn
REV:1.0 2008.03.13
Page 1 of 9
1 page  
www.DataSheet4U.com
SD42511
COMPONENTS SELECTION
1. Input Capacitor Selection
The input capacitor provides the pulse current when the power MOSFET is on, and charge the capacitor when
the power MOSFET is off, thus to keep the stability of the input voltage. The input capacitor is recommended to
be more than 10μF, which can reduce the peak current drawn from input source and the switch noise. The input
capacitor should be near to the input pin when in real routing.
2. Output Capacitor Selection
Parallel connecting a capacitor between the two ends of LED can reduce the output voltage ripple accordingly
reduce the ripple current of LED, while this capacitor will not effect the operating frequency and efficiency, but the
start time will be longer by reducing the rising speed of the voltage on LED. The larger the output capacitor is, the
smaller the current ripple on LED is. We recommend use the capacitor of 4.7μF.
3. Inductance Selection
The inductance is used to keep the output current constant, the bigger the inductance is, the smaller the output
current ripple is; while the bigger the physical size is, the bigger the series-wound resistor is. The selected
effective current (RMS current rating)of inductance current should be bigger than the maximum output current,
and the saturation current should be 30% bigger than maximum output current. In order to improve the efficiency,
the series-wound resistor (DCR) of inductance should be smaller than 0.2Ω.
The relation between inductance and ripple:
L
=
VOUT
*
VIN
VIN
− VOUT
* f * ΔI
Where: L: Inductance value
F: Oscillator frequency
ΔI is ripple current
When select inductance, you should consider the combination of various factors to select suitable inductance.
When output current is 1A, 47μH inductance is recommended.
4. Diode Selection
SD42511 is a non-synchronous step-down adjuster, so the diode should provide continuous current when the
power MOSFET is off. Because the forward voltage of Schottky diode is small, and the reverse continuous
current time is short, so it is usually used for continuous current. During the power MOSFET is conducting, the
diode will withstand high voltage, so the reverse voltage of selected diode should be bigger than the input voltage.
The average current through the diode is ID:
ID = (1− D) * ILED ILED is the current of LED
When the input voltage is high with a small duty, ID increases, so the selected maximum continuous current
diode should be bigger than the output current.
HANGZHOU SILAN MICROELECTRONICS CO.,LTD
Http://www.silan.com.cn
REV:1.0 2008.03.13
Page 5 of 9
5 Page | ||
| Páginas | Total 9 Páginas | |
| PDF Descargar | [ Datasheet SD42511.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| SD42511 | 1A WHITE LED DRIVER | Silan |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |