|
|
PDF UP550 Data sheet ( Hoja de datos )
| Número de pieza | UP550 | |
| Descripción | Program Controller User Manual | |
| Fabricantes | Yokogawa | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de UP550 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Instruction
Manualwww.DataSheet4U.com
Model UP550
Program Controller
User’s Manual for
Cascade Control
IM 05E01C02-44E
IM 05E01C02-44E
1st Edition
1 page  
<Int> <Rev>
Modelwww.DataSheet4U.com UP550
Program Controller
User’s Manual for Cascade Control
Toc-1
IM 05E01C02-44E 1st Edition
CONTENTS
1. Installation .............................................................................................. 1-1
1.1 Model and Suffix Codes .................................................................................. 1-1
1.2 How to Install ................................................................................................... 1-2
1.3 How to Connect Wires .................................................................................... 1-5
1.4 Hardware Specifications ................................................................................ 1-7
1.5 Terminal Wiring Diagrams ............................................................................ 1-13
2. Initial Settings ......................................................................................... 2-1
2.1 Names and Functions of Front Panel Parts ................................................... 2-2
2.2 Setting UP mode (Setting First at Power-on) ................................................. 2-3
2.3 Changing UP mode ......................................................................................... 2-4
2.4 Setting Primary and Secondary PV Input Types ........................................... 2-6
2.5 Setting Control Output Type
(except for a Position Proportional Controller) ........................................... 2-10
2.6 Calibrating Valve Position (for a Position Proportional Controller Only) .. 2-12
2.7 Initializing Parameters .................................................................................. 2-14
3. Programming .......................................................................................... 3-1
3.1 Overview of Program Patterns ....................................................................... 3-1
3.2 Example of Program Pattern Setup Charts ................................................... 3-2
3.3 Creating Program Patterns............................................................................. 3-4
3.4 Changing Program Patterns .......................................................................... 3-11
3.5 Program Parameter Map ............................................................................... 3-14
3.6 Lists of Program Parameters ....................................................................... 3-16
3.7 Program Pattern Setup Charts ..................................................................... 3-21
3.8 Explanation of Program Functions .............................................................. 3-24
4. Operations .............................................................................................. 4-1
4.1 Monitoring-purpose Operating Displays Available during Operation ......... 4-1
4.2 Performing/Canceling Auto-tuning of Secondary-loop .............................. 4-10
4.3 Performing/Canceling Auto-tuning of Primary-loop ................................... 4-12
4.4 Setting PID of Secondary-loop Manually ..................................................... 4-13
4.5 Setting PID of Primary-loop Manually .......................................................... 4-15
4.6 Selecting Program Pattern Number (PT.No) ................................................ 4-16
4.7 Switching between RUN and RESET Modes ............................................... 4-17
4.8 Switching between Cascade (CAS) and Local (LSP) .................................. 4-18
4.9 Switching between AUTO and MAN of Secondary-loop ............................. 4-19
IM 05E01C02-44E 1st Edition : May 31,2000-00
5 Page 
<Toc>
1.3 Howwww.DataSheet4U.com to Connect Wires
<1. Installation>
1-5
1)
CAUTION 2)
Before carrying out wiring, turn off the power to the controller and check that the
cables to be connected are not alive with a tester or the like because there is a possi-
bility of electric shock.
Wiring must be carried out by personnel who have basic electrical knowledge and
practical experience.
NOTE
1) Provide power from a single-phase instrument power supply. If there is a lot of noise in
the power line, insert an insulating transformer into the primary side of the line and use
a line filter (recommended part: ZAC2205-00U from TDK) on the secondary side.
As a countermeasures against noise, do not place the primary and secondary power
cables close to each other.
2) For thermocouple input, use shielded compensating lead wires for wiring. For RTD
input, use shielded wires that have low conductor resistance and cause no significant
differences in resistance between the three wires.
The cables to be used for wiring, terminal specifications, and recommended parts are
as shown below.
3) Control output relays may be replaced. However, because they have a life of 100,000
times that of the resistance load, use auxiliary relays to turn on/off a load.
4) The use of inductance (L) loads such as auxiliary relays, motors and solenoid valves
causes malfunction or relay failure; always insert a CR filter for use with alternating
current or a diode for use with direct current, as a spark-removal surge suppression
circuit, into the line in parallel with the load.
I For DC Relay Wiring
I For AC Relay Wiring
UP550
O.C Relay
External DC power supply
R
UP’s contact
Relay
(Use one with a relay coil
rating less than the UP’s
contact rating.)
Diode
(Mount it directly
to the relay coil
terminal (socket).)
UP550
External AC power supply
R
UP’s contact
Relay
(Use one with a relay coil
rating less than the UP’s
contact rating.)
CR filter
(Mount it directly
to the relay coil
terminal (socket).)
IM 05E01C02-44E 1st Edition : May 31,2000-00
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet UP550.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| UP550 | Program Controller | Yokogawa |
| UP550 | Program Controller User Manual | Yokogawa |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |