|
|
Número de pieza | NCP1294 | |
Descripción | Enhanced Voltage Mode PWM Controller | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de NCP1294 (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
No Preview Available ! NCP1294
Product Preview
Enhanced Voltage Mode
PWMwww.datasheet4u.com Controller
The NCP1294 fixed frequency feed forward voltage mode PWM
controller contains all of the features necessary for basic voltage mode
operation. This PWM controller has been optimized for high
frequency primary side control operation. In addition, this device
includes such features as: Soft−Start, accurate duty cycle limit control,
less than 50mA startup current, over and undervoltage protection, and
bidirectional synchronization. The NCP1294 is available in a 16 lead
SOIC narrow surface mount package.
Features
• 1.0 MHz Frequency Capability
• Fixed Frequency Voltage Mode Operation, with Feed Forward
• Thermal Shutdown
• Undervoltage Lock−Out
• Accurate Programmable Max Duty Cycle Limit
• 1.0 A Sink/Source Gate Drive
• Programmable Pulse−By−Pulse Overcurrent Protection
• Leading Edge Current Sense Blanking
• 75 ns Shutdown Propagation Delay
• Programmable Soft−Start
• Undervoltage Protection
• Overvoltage Protection with Programmable Hysteresis
• Bidirectional Synchronization
• 25 ns GATE Rise and Fall Time (1.0 nF Load)
• 3.3 V 3% Reference Voltage Output
• Pb−Free Packages are Available*
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
© Semiconductor Components Industries, LLC, 2009
April, 2009 − Rev. P0
1
http://onsemi.com
16
1
SOIC−16
D SUFFIX
CASE 751B
TSSOP−16
16 DTB SUFFIX
CASE 948F
1
PIN CONNECTIONS AND
MARKING DIAGRAM
1
GATE
ISENSE
SYNC
FF
UV
OV
16
VC
PGND
VCC
VREF
LGND
SS
RTCT
ISET
COMP
VFB
1 16
NCP1294= Specific Device Code
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
G = Pb−Free Package
ORDERING INFORMATION
Device
Package Shipping†
NCP1294ED16
SOIC−16 48 Units / Rail
NCP1294ED16G
NCP1294EDR16
SOIC−16 48 Units / Rail
(Pb−Free)
SOIC−16 2500 Tape & Reel
NCP1294EDR16G
NCP1294EDTB16G
SOIC−16 2500 Tape & Reel
(Pb−Free)
TSSOP−16 96 Units / Rail
(Pb−Free)
NCP1294EDTB16R2G TSSOP−16 2500 Tape & Reel
(Pb−Free)
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
Publication Order Number:
NCP1294/D
1 page NCP1294
ELECTRICAL CHARACTERISTICS (−40°C < TA < 85°C; −40°C < TJ < 125°C; 3.0 V < VC < 15 V; 4.7 V < VCC < 15 V;
RT = 12 k; CT = 390 pF; unless otherwise specified.)
Characteristic
Test Conditions
Min Typ
Max
Gate Driver
High Saturation Voltage
Low Saturation Voltage
www.datasHheigeht4Vuo.cltoamge Clamp
VC − GATE, VC = 10 V, ISOURCE = 200 mA
GATE − PGND, ISINK = 200 mA
−
− 1.5 2.0
− 1.2 1.5
11 13.5
16
Output Current
1.0 nF Load. Note 3
− 1.0 1.25
Output UVL Leakage
GATE = 0 V
− 1.0 50
Rise Time
Fall Time
Max Gate Voltage During UVL/Sleep
Feed Forward (FF)
1.0 nF Load, VC = 20 V, 1.0 V < GATE < 9.0 V
1.0 nF Load, VC = 20 V, 9.0 V < GATE < 1.0 V
IGATE = 500 mA
−
−
0.4
60
25
0.7
100
50
1.0
Discharge Voltage
Discharge Current
IFF = 2.0 mA
FF = 1.0 V
− 0.3
2.0 16
0.7
30
FF to GATE Delay
− 50 75 125
Overcurrent Protection
Overcurrent Threshold
ISENSE to GATE Delay
External Voltage Monitors
ISET = 0.5 V, Ramp ISENSE
−
0.475
50
0.5
90
0.525
125
Overvoltage Threshold
OV Increasing
1.9 2.0
2.1
Overvoltage Hysteresis Current
OV = 2.15 V
10 12.5
15
Undervoltage Threshold
UV Increasing
0.95 1.0
1.05
Undervoltage Hysteresis
− 25 75 125
Soft−Start (SS)
Charge Current
SS = 2.0 V
40 50
70
Discharge Current
SS = 2.0 V
4.0 5.0
7.0
Charge Voltage
−
2.8 3.0
3.4
Discharge Voltage
−
0.25 0.3
0.35
Soft−Start Clamp Offset
FF = 1.25 V
1.15 1.25
1.35
Soft−Start Fault Voltage
OV = 2.15 V or LV = 0.85 V
− 0.1 0.2
Blanking
Blanking Time
− 50 150 250
SS Blanking Disable Threshold
COMP Blanking Disable Threshold
Thermal Shutdown
VFB < 1.0
VFB < 1.0, SS > 3.0 V
2.8 3.0
2.8 3.0
3.3
3.3
Thermal Shutdown
Note 3
125 150
180
Thermal Hysteresis
Note 3
5.0 10
15
3. Guaranteed by design, not 100% tested in production.
Unit
V
V
V
A
mA
ns
ns
V
V
mA
ns
V
ns
V
mA
V
mV
mA
mA
V
V
V
V
ns
V
V
°C
°C
http://onsemi.com
5
5 Page NCP1294
800
700
600
RT = 5.0 K
500
400
RT = 10 K
www.datashe3e0t04u.com
200
100
0
0.0001
RT = 50 K
0.001
CT (mF)
0.01
Figure 10. Typical Performance Characteristics,
Oscillator Frequency vs. CT
that during steady state, VCOMP doesn’t change for input
voltage variations. This intuitively explains why FF voltage
mode control has superior line regulation and line transient
response. Knowing the nominal value of VIN and TON, one
can also select the value of RC to place VCOMP at the center
of its dynamic range.
Select Feedback Voltage Divider
As shown in Figure 12, the voltage divider output feeds to
the FB pin, which connects to the inverting input of the error
amplifier. The non−inverting input of the error amplifier is
connected to a 1.27 V (typ) reference voltage. The FB pin
has an input current which has to be considered for accurate
DC outputs. The following equation can be used to calculate
the R1 and R2 value
ǒ ǓR2
R1 ) R2
VOUT
+ 1.27 * ʼn
where ∇ is the correction factor due to the existence of the
FB pin input current Ier.
ʼn + (Ri ) R1ńńR2)Ier
Ri = DC resistance between the FB pin and the voltage
divider output.
Ier = VFB input current, 1.3 mA typical.
Design Voltage Dividers for OV and UV Detection
In Figure 13, the voltage divider uses three resistors in
series to set OV and UV threshold seen from the input
voltage. The values of the resistors can be calculated from
the following three equations, where the third equation is
derived from OV hysteresis requirement.
ǒ ǓVIN(LOW)
R2 ) R3
R2 ) R3 ) R1
+ 1.0 V
(A)
ǒ ǓVIN(HIGH)
R3
R2 ) R3 ) R1
+ 2.0 V
(B)
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0.65
0.60
0.55
0.50
1000
10000
100000
RT (W)
1000000
Figure 11. Typical Performance Characteristics,
Oscillator Duty Cycle vs. RT
12.5 mA (R1 ) R2) + VHYST
(C)
where:
VIN(LOW), VIN(HIGH) = input voltage OV and UV
threshold;
VHYST = OV hysteresis seen at VIN
It is self−evident from equation A and B that to use this
design, VIN(HIGH) has to be two times greater than
VIN(LOW). Otherwise, two voltage dividers have to be used
to program OV and UV separately.
COMP
VOUT
Ier R1
− Ri
FB
+
+
−
1.27
R2
Figure 12. The Design of Feedback Voltage Divider
Has to Consider the Error Amplifier Input Current
R1 R2 R3
VIN
VUV
VOV
Figure 13. OV/UV Monitor Divider
http://onsemi.com
11
11 Page |
Páginas | Total 13 Páginas | |
PDF Descargar | [ Datasheet NCP1294.PDF ] |
Número de pieza | Descripción | Fabricantes |
NCP1294 | Enhanced Voltage Mode PWM Controller | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |