DataSheetWiki

WJA1035 Datasheet دیتاشیت PDF دانلود

دیتاشیت - WJ Communication - 5V Active-Bias InGaP HBT Gain Block

شماره قطعه WJA1035
شرح مفصل 5V Active-Bias InGaP HBT Gain Block
تولید کننده WJ Communication 
آرم WJ Communication 


1 Page

		

No Preview Available !

WJA1035 شرح
WJA1035
+5V Active-Bias InGaP HBT Gain Block
Product Features
50 – 4000 MHz
15 dB Gain
www.data+s1h6eedtB4um.coPm1dB
+36 dBm OIP3
+5V Single Voltage Supply
Internal Active Bias Supply
Internally matched to 50 Ω
Lead-free / RoHS-compliant /
Green SOT-89 package
Applications
GSM, PCS, CDMA, WCDMA
WiMAX, WiBro
Repeaters, BTS Transceivers
RFID
Product Description
Functional Diagram
The WJA1035 is a cascadable gain block that offers high
linearity in a low-cost surface-mount package. At 1.9 GHz,
the WJA1035 typically provides 15 dB gain, +36 dBm
OIP3, and +16 dBm P1dB. The device is housed in a lead-
free/green/RoHS-compliant SOT-89 industry-standard
SMT package using a NiPdAu plating to eliminate the
possibility of tin whiskering.
The WJA1035 consists of Darlington pair amplifiers using
a high reliability InGaP/GaAs HBT process technology.
The MMIC amplifier is internally matched to 50and only
requires DC-blocking capacitors and a bias inductor for
operation. An internal active bias is designed to enable
stable performance over temperature. A dropping bias
resistor is not required allowing the device to be biased
directly from a +5V supply voltage.
GND
4
1
RF IN
2
GND
3
RF OUT
Function
Input
Output/Bias
Ground
Pin No.
1
3
2, 4
The broadband amplifier can be directly applied to various
current and next generation wireless technologies such as
GSM, CDMA, W-CDMA, WiBro, and WiMAX. The
WJA1035 is ideal for general purpose applications such as
LO buffering, IF amplification and pre-driver stages within
the 50 to 4000 MHz frequency range.
Specifications
Parameter
Operational Bandwidth
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output P1dB
Output IP3 (2)
Noise Figure
Device Voltage
Device Current
Units
MHz
MHz
dB
dB
dB
dBm
dBm
dB
V
mA
Min
50
Typ
1900
14.8
19
16
+16.1
+35.6
6.2
5
65
Max
4000
1. Test conditions: 25 ºC, Supply Voltage = +5.00 V, 50 Ω System.
2. 3OIP measured with two tones at an output power of 0 dBm/tone separated by 1 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
3. S-parameters and 3OIP measured at device pins. All other specifications measured on evaluation
board.
Typical Performance
Parameter
Frequency
S21
S11
S22
Output P1dB
Output IP3 (2)
Noise Figure
Units
MHz
dB
dB
dB
dBm
dBm
dB
500
14.3
-14
-19
+18.4
+36.9
5.3
Typical
900 1900
14.2 14
-17 -19
-19 -10
+17.6 +16.1
+35.6 +34.6
5.7 6.2
1. Listed typical performance parameters measured on evaluation board.
2100
14
-19
-10
+15.5
+34.5
6.8
Absolute Maximum Rating
Parameter
Operating Case Temperature
Storage Temperature
Supply Voltage
Input Power
Rating
-40 to +85 °C
-55 to +150 °C
+6.5 V
+24 dBm
Ordering Information
Part No.
WJA1035
WJA1035-PCB
Description
+5V Active Bias InGaP HBT Gain Block
(lead-free/green/RoHS-compliant SOT-89 Package)
50 – 4000 MHz Fully Assembled Eval. Board
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice
WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: sales@wj.com Web site: www.wj.com
Page 1 of 4 Aug 2007

قانون اساسیصفحه 4
دانلود [ WJA1035 دیتاشیت ]



دیتاشیت توصیه

شماره قطعه شرح مفصل تولید کنندگان
WJA1030 5V Active-Bias InGaP HBT Gain Block WJ Communication
WJ Communication
WJA1035 5V Active-Bias InGaP HBT Gain Block WJ Communication
WJ Communication

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2018   |   تماس با ما  |   جستجو