|
|
Numéro de référence | W130L | ||
Description | Sensick | ||
Fabricant | Sick | ||
Logo | |||
1 Page
04 06
W130L
Do not stare into the laser beam directly, install at
eye-level of the people around, nor expose the beam to
the human body intentionally.
Use the exclusive amplifier unit to connect the product.
Not doing so may result in an accident or product damage.
Wiring or disconnecting with the power ON is danger.
Never fail to turn OFF the power supply.
This product cannot be used as a safety device to
protect human body.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Precautions in using WSE130L
When using WSE130L-32/34 or WSE130L-52/54 for length measurement, follow
the instructions below.
Emitter is applied to gray cable and Receiver is applied to black one.
Install the sensor so that the sensor of flood beam is positioned in the center of
the light receiving part. (Install so that the indication value of amplifier unit is
maximum.)
Install the flooding/receiving device in the same direction.
Refer to each label or indicator light as a standard.
Indicator light
Indicator light
P41F Reflector (WL130L-32)
Instruction for use
1. When cleaning, blow off or lightly wipe with a soft cloth.
Do not use thinner, benzene or kerosene.
2. Avoid strong push of the reflecting surface or direct impact.
Doing so may result in damaging the prism and deteriorating the performance.
3. Avoid using outside or under the environment where oil or water scatters.
Installation procedure
Refer to the figure below and use in the correct direction.
Improper installation may cause malfunction.
Australia
Phone +61 3 9497 4100
E-Mail: [email protected]
Belgium/Luxembourg
Phone +32 (0)2 466 55 66
E-Mail: [email protected]
Brasil
Phone +55 11 5091-4900
E-Mail: [email protected]
Ceská Republika
Phone +420 2 57 91 18 50
E-Mail: [email protected]
China
Phone +852-2763 6966
E-Mail: [email protected]
Danmark
Phone +45 45 82 64 00
E-Mail: [email protected]
Deutschland
Phone +49 (0)2 11 53 01-0
E-Mail: [email protected]
España
Phone +34 93 480 31 00
E-Mail: [email protected]
France
Phone +33 1 64 62 35 00
E-Mail: [email protected]
Great Britain
Phone +44 (0)1727 831121
E-Mail: [email protected]
India
Phone +91 –22– 2822 7084
E-Mail: [email protected]
Italia
Phone +39 02 27 40 93 19
E-Mail: [email protected]
Japan
Phone +81 (0)3 3358 1341
E-Mail: [email protected]
Nederlands
Phone +31 (0)30 229 25 44
E-Mail: [email protected]
Norge
Phone +47 67 81 50 00
E-Mail: [email protected]
Österreich
Phone +43 (0)22 36 62 28 8-0
E-Mail: [email protected]
Polska
Phone +48 22 837 40 50
E-Mail: [email protected]
Republic of Korea
Phone +82-2 786 6321/4
E-Mail: [email protected]
Republika Slowenija
Phone +386 (0)1-47 69 990
E-Mail: [email protected]
Russia
Phone +7 95 775 05 30
E-Mail [email protected]
Schweiz
Phone +41 41 619 29 39
E-Mail: [email protected]
Singapore
Phone +65 6744 3732
E-Mail: [email protected]
Suomi
Phone +358-9-25 15 800
E-Mail: [email protected]
Sverige
Phone +46 8 680 64 50
E-Mail: [email protected]
Taiwan
Phone +886 2 2365-6292
E-Mail: [email protected]
Türkiye
Phone +90 216 388 95 90 pbx
E-Mail: [email protected]
USA/Canada/México
Phone +1(952) 941-6780
E-Mail: [email protected]
More representatives and agencies
in all major industrial nations at
www.sick.com
We reserve the right to make changes without prior notification
For further information regarding the configuration menu and
teaching function please take note of the handbook. Available on
the internet at www.sick.com or from your contact person at SICK.
Safety Precautions
Carefully read and understand the safety precautions before operation.
The important information is provided to protect your health and property.
Do not apply any other installing or operating procedure other than that described
in this manual.
Meanings of Safety Symbols
WARNING
Indicates a possible hazard that may result in death,
serious injury, or serious property damage if the pro-
duct is used without observing the stated instructions.
CAUTION
Indicates a possible hazard that may result in
personal injury or property damage if the product is
used without observing the stated instructions.
Mandatory Requirements
WARNING
This product is not an explosion-proof construction. Do
not use the product under flammable, explosive gas or
liquid environment.
Use of controls or adjustments or performance of pro-
cedures other than those specified herein may result
in hazardous radiation exposure.
The light source of this product applies the visible light
semiconductor laser.
Do not disassemble or modify the product since it is
not designed to automatically stop the laser emission
when open. Disassembling or modifying at customer's
end may cause personal injury, fire or electric shock.
Operating Precautions
CAUTION
Installing in the following places may result in malfunction:
1. A dusty or steamy place
2. A place generating corrosive gas
3. A place directly receiving scattering water or oil
4. A place suffered from heavy vibration or impact
Do not use the sensor outside nor expose the detection
surface directly to ambient light (laser light, incandes-
cent light and sunlight).
Do not use the sensor in transient state after power on
(approx. 100 ms).
The sensor performance may depend on the individual
units.
Wipe off dirt on the emitting/receiving parts to maintain
correct detection. Also, avoid direct impact on the
product.
Precautions for using laser
Laser emission warning light
Confirmation of laser emission is available with the laser emission warning light.
It starts lighting after turning the power on and keeps lighting while the laser is
being radiated. It is also possible to confirm with the exclusive amplifier unit.
Laser radiation warning light (Green)
Laser label
This product is classified as a Class 2 (II) Laser Product by JIS C6802 / IEC / FDA
Laser Safety Standard as this radiates the visible laser beam. The warning label and
the description label in English are attached on the side face of the sensor head
indicating the CLASS 2/Class II.
*The emitters WS130L-34 and WS130L-54 of WSE130L-32/34 and WSE130L-52/54 are rated
as Class II by the FDA standard (when exporting to the US). However, the class 1 is applied for the
JIS/IEC standard.
When exporting this machine to the US, the US laser control, FDA (Food and Drug
Administration) is applied. This product has been already reported to CDRH (Center
for Devices and Radiological Health). For details, contact our Customer Service.
WT130L-32
WL130L-32
WSE130L-32
WSE130L-34
WSE130L-52
WSE130L-54
Indicator light
Specifications
Model
Retro
Diffuse
Through beam Through beam
reflection type reflection type
SPOT
LINE
Cable
WL130L
WT130L
WSE130L-32
WS130L-32
WE130L-32
WSE130L-52
WS130L-52
WE130L-52
M8 Relay-type
-
-
WSE130L-34
WSE130L-54
Emitter M8
-
-
WS130L-34
WS130L-54
Detector M8
-
-
WE130L-34
WE130L-54
Adaptable amplifier unit
WI130
Light source
Visible light semiconductor laser 650 nm
Output
max. 3 mW
max. 390 μW
IEC/JIS CLASS
CLASS 2
CLASS 1
FDA CLASS
Class II
Detection Long
distance Standard
*1 Fast
8m
5m
2m
1m
0.7 m
0.25 m
2m
2m
Length measurement
mode: 0.5 m
(Only Long and Standard)
Beam size
Approx. 2 mm Ø Approx. 1 mm Ø Approx. 2 mm Ø Approx. 30 x 2.5 mm
*2
(Distance: 2 m) (Distance: 1 m) (Distance: 2 m) (Distance: 2 m)
Repeat accuracy *3
0.2 mm
0.2 mm
0.2 mm
0.3 mm
Indicator light
Laser radiation indictor light: Green Output indicator light: Orange
Operating temperature/humidity
-10 to +55°C/35 to 85 %RH (No condensation or freezing)
Store temperature/humidity
-25 to +70°C/35 to 85 %RH (No condensation or freezing)
Ambient light
3,000 lx (Incandescent light) 10,000 lx (Sunlight)
Shock resistance 10 to 55 Hz Double-amplitude 1.5 mm 2 hours at each direction of X, Y and Z
Protection category
IP67
Material
Weight (including the codes) *4
PC (Case, Cover) PMMA / Glass (Front glass)
45 g 90 g 115 g
* 1 WT130L-32 : With white paper (90 %) of 200 x 200 mm
WL130L-32 : With the reflector P41F (accessory)
* 2 Defined with center strength 1/e2 (13.5 %). There may be leak light other than the specified spot size. The
sensor may be damaged when there is a highly reflective object around the targets
* 3 Right angle to sensing axis (to 2 m).
* 4 The weights of WSE130L types include the emitter and receiver.
(1)
FDA warning /
Laser open label (1)(2)
(3)
(2)
FDA warning / Laser open /
Certification label (3)
Accessories and others
Lens attachment (Optional)
Installing the attachment to WL130L-32 allows two types of beam shape: Line beam
and area beam. Attach the beam-shape lens and the optical axis to use together.
Line beam lens
Area beam lens
Beam shape
Line beam
Area beam
Approx. 40 x 1 mm
(Distance: 300 mm)
Approx. 35 x 35 mm
(Distance: 300 mm)
The beam shape may depend on the individual products.
Do not use for WT130L-32. Uninstallable to WSE130L-52/54.
Dimensional drawing
WT130L-32
WL130L-32
WSE130L-32
WSE130L-34
34.6
19.1 12.7
ø 3.2
11.2
ø 3.2
28.1
34.6
21
16.1
WSE130L-52
WSE130L-54
52.9
25.9
46.4
ø 3.2
2.7
9.9
31.65
31.65
ø 3.2
P41F
14.5
P250F
47
7.4
23 ø 3.2
29
4.5
10 20 10
51.6
3.5
7.1
The product specification may change without notice for improvement.
For any inquiry, please contact the manufacture/vendor below.
|
|||
Pages | Pages 1 | ||
Télécharger | [ W130L ] |
No | Description détaillée | Fabricant |
W130 | Spread Spectrum Desktop/Notebook System Clock | Cypress Semiconductor |
W13009 | STW13009 | STMicroelectronics |
W130L | Sensick | Sick |
US18650VTC5A | Lithium-Ion Battery | Sony |
TSPC106 | PCI Bus Bridge Memory Controller | ATMEL |
TP9380 | NPN SILICON RF POWER TRANSISTOR | Advanced Semiconductor |
www.DataSheetWiki.com | 2020 | Contactez-nous | Recherche |