|
|
PDF DS1813 Data sheet ( Hoja de datos )
| Número de pieza | DS1813 | |
| Descripción | 5V EconoReset | |
| Fabricantes | Dallas Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de DS1813 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
www.dalsemi.com
DS1813
5V EconoReset with Pushbutton
FEATURES
Automatically restarts a microprocessor after
power failure
Monitors pushbutton for external override
Maintains reset for typically 150 ms after VCC
returns to an in-tolerance condition
Reduces need for discrete components
Precision temperature-compensated voltage
reference and voltage sensor
Low-cost TO-92 or space saving surface-
mount SOT-23 packages available
Efficient open-drain output with internal
5.5 kΩ=pull-up resistor
Operating temperature -40°C to +85°C
PIN ASSIGNMENT
3
12
SOT-23 PACKAGE
123
123
TO-92 PACKAGE
See Mech.
Drawings Section
PIN DESCRIPTION
TO-92
1 RST
2 VCC
3 GND
Active Low Reset Output
Power Supply
Ground
SOT-23
1 RST
2 VCC
3 GND
Active Low Reset Output
Power Supply
Ground
DESCRIPTION
The DS1813 EconoReset uses a precision temperature reference and comparator circuit to monitor the
status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail
signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition,
the reset signal is kept in the active state for approximately 150 ms to allow the power supply and
processor to stabilize.
The DS1813 also monitors a pushbutton on the reset output. If the reset line is pulled low, a reset is
generated upon release and will be held in reset output low for typically 150 ms.
1 of 5
111999
1 page  
NOTES:
1. All voltages are referenced to ground.
2. wMwwe.DasautarSehdeewt4Uit.hcoVm CC ≥ 2.7 volts.
3. A 1kΩ=external resistor may be required in some applications for proper operation of the
microprocessor reset control circuit.
DS1813
4. Measured with RST output open.
5. tR = 5 µs.
6. VOH and IOH are a function of the value of RP and the associated output load conditions.
7. This value is for reference in defining values for TRPD and should not be considered a requirement for
proper operation or use of the device.
PART MARKING CODES
“A”, “B”, &“C” represent the device type.
810 . . . . DS1810
811 . . . . DS1811
812 . . . . DS1812
813 . . . . DS1813
815 . . . . DS1815
816 . . . . DS1816
817 . . . . DS1817
818 . . . . DS1818
“D” represents the device tolerance.
A . . . . . . 5%
B . . . . . . 10%
C . . . . . . 15%
D . . . . . . 20%
5 of 5
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet DS1813.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| DS1810 | 5V EconoReset | Dallas Semiconductor |
| DS1811 | 5V EconoReset | Dallas Semiconductor |
| DS1812 | 5V EconoReset | Dallas Semiconductor |
| DS1813 | 5V EconoReset | Dallas Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |