DataSheetWiki


VNH3ASP30-E fiches techniques PDF

STMicroelectronics - AUTOMOTIVE FULLY INTEGRATED H-BRIDGE MOTOR DRIVER

Numéro de référence VNH3ASP30-E
Description AUTOMOTIVE FULLY INTEGRATED H-BRIDGE MOTOR DRIVER
Fabricant STMicroelectronics 
Logo STMicroelectronics 





1 Page

No Preview Available !





VNH3ASP30-E fiche technique
Table 1. General Features
TYPE
www.DataSheet4U.com
VNH3ASP30-E
RDS(on)
42 mmax
(per leg)
IOUT
30 A
VNH3ASP30-E
AUTOMOTIVE FULLY INTEGRATED
H-BRIDGE MOTOR DRIVER
Vccmax
41 V
Figure 1. Package
TARGET SPECIFICATION
s OUTPUT CURRENT: 30A
s 5V LOGIC LEVEL COMPATIBLE INPUTS
s UNDERVOLTAGE AND OVERVOLTAGE
SHUT-DOWN
s OVERVOLTAGE CLAMP
s THERMAL SHUT DOWN
s CROSS-CONDUCTION PROTECTION
s LINEAR CURRENT LIMITER
s VERY LOW STAND-BY POWER
CONSUMPTION
s PWM OPERATION UP TO 20 KHz
s PROTECTION AGAINST:
LOSS OF GROUND AND LOSS OF VCC
s CURRENT SENSE OUTPUT PROPORTIONAL
TO MOTOR CURRENT
s IN COMPLIANCE WITH THE 2002/95/EC
EUROPEAN DIRECTIVE
DESCRIPTION
The VNH3ASP30-E is a full bridge motor driver
intended for a wide range of automotive
applications. The device incorporates a dual
monolithic High-Side drivers and two Low-Side
switches. The High-Side driver switch is designed
using STMicroelectronic’s well known and proven
proprietary VIPowerM0 technology that allows
to efficiently integrate on the same die a true
Power MOSFET with an intelligent signal/
protection circuitry.
MultiPowerSO-30
The Low-Side switches are vertical MOSFETs
manufactured using STMicroelectronic’s
proprietary EHD (‘STripFET™’) process. The
three dice are assembled in MultiPowerSO-30
package on electrically isolated leadframes. This
package, specifically designed for the harsh
automotive environment offers improved thermal
performance thanks to exposed die pads.
Moreover, its fully symmetrical mechanical design
allows superior manufacturability at board level.
The input signals INA and INB can directly
interface to the microcontroller to select the motor
direction and the brake condition. The DIAGA/ENA
or DIAGB/ENB, when connected to an external
pull-up resistor, enable one leg of the bridge. They
also provide a feedback digital diagnostic signal.
The normal condition operation is explained in the
truth table on page 7. The CS pin allows to monitor
the motor current by delivering a current
proportional to its value. The PWM, up to 20KHz,
lets us to control the speed of the motor in all
possible conditions. In all cases, a low level state
on the PWM pin will turn off both the LSA and LSB
switches. When PWM rises to a high level, LSA or
LSB turn on again depending on the input pin
state.
Table 2. Order Codes
Package
MultiPowerSO-30
Tube
VNH3ASP30-E
Tape and Reel
VNH3ASP30TR-E
September 2004
Rev. 1
1/18

PagesPages 18
Télécharger [ VNH3ASP30-E ]


Fiche technique recommandé

No Description détaillée Fabricant
VNH3ASP30-E AUTOMOTIVE FULLY INTEGRATED H-BRIDGE MOTOR DRIVER STMicroelectronics
STMicroelectronics

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche