DataSheetWiki


ICM450 fiches techniques PDF

ICM - 3-Phase Voltage Monitor

Numéro de référence ICM450
Description 3-Phase Voltage Monitor
Fabricant ICM 
Logo ICM 





1 Page

No Preview Available !





ICM450 fiche technique
ICM450
THREE-PHASE VOLTAGE MONITOR
Stop Motor Burnouts!
Programmable 3-phase line voltage monitor
with 25-fault memory, high temperature LCD
display, easy setup & clear, diagnostic readout
of system faults, 190 to 630 VAC operation...
The ICM450 was specifically designed to protect motors and
other 3-phase loads from premature failure and damage due
to common voltage faults such as voltage unbalance, over/
under voltage, phase loss, reversal, incorrect sequencing and
rapid short cycling.
www.DataSheet4U.com
Mode of Operation
At power up, the ICM450 evaluates the incoming power for proper phase sequence, amplitude, and symmetry (voltage
unbalance). If the three phase input at the line side connections is within user-set parameters, the load energize LED is
turned on and the internal relay is energized. Continuity will be across terminals 4 and 6. If connections are made to the
load side terminals, the ICM450 will transfer monitoring over to the load side only.
When a critical fault condition (phase loss or phase reversal) is present, the relay will immediately de-energize, the load-
energized LED will turn off, the fault LED will flash, and the fault is written to memory. Continuity will be across terminals
4 and 5.
If a non-critical fault condition (unbalance, high or low voltage) is present, the ICM450 will ignore it during the interro-
gation delay time. If it is still present following the interrogation delay time, the relay will de-energize, the load-energized
LED will turn off, the fault LED will flash, and the fault is written to memory. Continuity will be across terminals 4 and 5.
The ICM450 will store the last 25 faults in memory. The relay will not energize if any fault conditions exist. The integral
adjustable delay on break timer will prevent short cycling.
Features
Wiring Diagram
• Reliable, high temperature LCD display
– Simplifies system setup and diagnostics. Indicates
condition of incoming line voltage, fault conditions,
system setpoints and other user adjustments.
– Temperature: -20°C to +75°C (-4°F to + 167°F)
• Simultaneous voltage display (an ICM exclusive)
– View all 3 phases, no need to scroll through readouts.
• Fully adjustable variables
– User may easily set and adjust variables in SETUP
mode:
• Line voltage: 190 to 600 VAC
• Voltage unbalance: 2 to 20%
• Delay on break period: 0 to 10 minutes
• Fault interrogation: 0 to 15 seconds
• Over/under voltage: 2 to 25%
• Reset modes: AUTO or 0 to 10 retries
• Control mode: ON or OFF
• 25-fault memory and storage
– Clearly displayed on LCD
• Ultra bright LED indicators
– Shows current mode:
• Setup LED
• Load energized LED
• Control voltage LED • Fault LED
• Easy to install and configure
– Simple 7-step push-button setup
– Wiring diagram on unit
– Installation and application guide included
*
Control
Voltage
L01
L02
L03
* Thermostat, pressure switch, etc.
LIS39-2
All features and specifications subject to change without notice.
Phone
315.233.5266
8A0pp0lic.a3tio6n5As.s5is5tan2ce5
visit us at: www.icmcontrols.com
Fax
315.233.5276
LI3
LI2
LI1
L0AD

PagesPages 2
Télécharger [ ICM450 ]


Fiche technique recommandé

No Description détaillée Fabricant
ICM450 3-Phase Voltage Monitor ICM
ICM

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche