|
|
Número de pieza | LUE50333 | |
Descripción | LED Lamps | |
Fabricantes | ETC | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LUE50333 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
No Preview Available ! WENRUN LED Lamps L 503
Features:
High speed response.
High reliability and long life.
Low power consumption.
Available in red,blue,white ,green, yellow colors.
Suitable for pulse operation.
Series
www.DataSheet4U.com
Descriptions:
The LED lamps are available with different colors,intensities,epoxy colors,etc.
The series specially designed for applications requiring higher brightness.
Superior performance in outdoor environment.
Applications:
These lamp are widely used for various application.
Board for display.
Indication of all kinds.
Traffic Signal.
Selection Guide:
Part No.
LUE50333
LUY50333
LAG50333
LAM50333
Material
AlGaInP
AlGaInP
AlGaInP
AlGaInP
Chip
Emitting Color
High Super Red
High Super Yellow
High Super Green
High Super Amber
Lens Type
Water Clear
Prepared date June 2005
http://www.wenrun.com
Rev. 3
Page 1of 5
1 page Label Form Specification
WENRUN LED Lamps L 503 Series
www.DataSheet4U.com
WENRUN OPTO.
TYPE Lxxxxxx
QUTY xxxxPCS
CODE xxxxxxxx
DATE xxxxxx
Manufacturer
Part No.
Quantity
Classing Code
Sealing Date (year-month-day)
Precautions In Use
A Soldering Conditions
1 When soldering, leave the minimum clearance between the bottom of the resin and the soldering point.
2 Maximum allowable soldering conditions are.
Solder dipping: 260 max., 5 seconds max., one time.
Soldering iron: 350 max., 5 seconds max., one time.
3 Contact between molten solder and the resin must be avoided.
4 In soldering, do not put any stress on the lead frame, particularly when heated.
B Lead frame Forming and Use
1 When forming leads ,the leads should be bent at a point at least 3mm from the base of epoxy. Lead
forming should be done before soldering.
2 Do not apply any bending stress to the base of the lead. The stress to the base may damage the LEDs
characteristics.
3 When mounting the LEDs onto a printed circuit board ,the holes on the circuit board should be exactly
aligned with the leads of the LEDs.
4 Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or
discoloration may cause difficulty during soldering operations. It is recommended that the LEDs be used as
soon as possible.
5 Please avoid rapid transitions in ambient temperature, especially, in high humidity environments.
Notes:
1 Above specification may be changed without notice. We will reserve authority on material change for
above specification.
2 When using this product, please observe the absolute maximum ratings and the instructions for the
specification sheets. We assume no responsibility for any damage resulting from use of the product which
does not comply with the instructions included in the specification sheets.
Prepared date June 2005
http://www.wenrun.com
Rev. 3
Page 5of 5
5 Page |
Páginas | Total 5 Páginas | |
PDF Descargar | [ Datasheet LUE50333.PDF ] |
Número de pieza | Descripción | Fabricantes |
LUE50333 | LED Lamps | ETC |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |