|
|
PDF JANTX2N688 Data sheet ( Hoja de datos )
| Número de pieza | JANTX2N688 | |
| Descripción | JANTX2N688 | |
| Fabricantes | ETC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de JANTX2N688 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
INCH-POUND
MIL-PRF-19500/108K
4 December 2006
SUPERSEDING
MIL-PRF-19500/108J
14 March 2006
PERFORMANCE SPECIFICATION SHEET
SEMICONDUCTOR DEVICE, THYRISTORS (CONTROLLED RECTIFIERS), SILICON,
TYPES 2N682, 2N683, 2N685 THROUGH 2N692, 2N692A, 2N5206, JAN AND JANTX
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein shall consist of
this specification sheet and MIL-PRF-19500.
1. SCOPE
1.1 Scope. This specification covers the performance requirements for PNPN silicon power, reverse-blocking
triode thyristors. Two levels of product assurance are provided for each device type as specified in MIL-PRF-19500.
1.2 Physical dimensions. See figure 1 (TO-208 stud, formerly TO-48).
1.3 Maximum ratings. TA = 25°C unless otherwise stated.
IO (1)
ITSM (2) VGM TJ TSTG
di/dt
t = 7 ms
(repetitive)
A
A
V (pk) °C
°C
A/µs
Min
Max 16
-65 -65
150 5 +125 +150
5
(1) This average forward current is for a maximum case temperature of +65°C, and 180 electrical degrees of
conduction.
(2) Surge rating is non-recurrent and applies only with device in the conducting state. The peak rate of surge
current must not exceed 100 amperes during the first 10 µs after switching from the off (blocking) state to
the on (conducting) state. This time is measured from the point where the thyristor voltage has decayed to
90 percent of its initial blocking value.
Comments, suggestions, or questions on this document should be addressed to Defense Supply Center,
Columbus, ATTN: DSCC-VAC, P.O. Box 3990, Columbus, OH 43218-3990, or emailed to
[email protected]. Since contact information can change, you may want to verify the currency of
this address information using the ASSIST Online database at http://assist.daps.dla.mil/ .
AMSC N/A
FSC 5961
1 page  
www.DataSheet4U.com
MIL-PRF-19500/108K
3.6 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance
characteristics are as specified in 1.3, 1.4, and table I.
3.7 Electrical test requirements. The electrical test requirements shall be as specified in table I herein.
3.8 Workmanship. Semiconductor devices shall be processed in such a manner as to be uniform in quality and
shall be free from other defects that will affect life, serviceability, or appearance.
4. VERIFICATION
4.1 Classification of inspections. The inspection requirements specified herein are classified as follows:
a. Qualification inspection (see 4.2).
b. Screening (see 4.3).
c. Conformance inspection (see 4.4).
4.2 Qualification inspection. Qualification inspection shall be in accordance with MIL-PRF-19500 and as specified
herein.
* 4.3 Screening (JANTX level). Screening shall be in accordance with appendix E, table E-IV of MIL-PRF-19500,
and as specified herein. The following measurements shall be made in accordance with table I herein. Devices that
exceed the limits of table I herein shall not be acceptable.
Screen
(see table E-IV of
MIL-PRF-19500)
Measurement
JANTX level
3a Method 1051 of MIL-STD-750, condition F, 20 cycles.
10 Not required
11 IRRM1, IDRM1, VGT1, VTM, and IGT1
12 Method 1040 of MIL-STD-750, condition A, TC = +125°C minimum, RGK ≥ 1K Ω;
VDRM, VRRM = rated (see 1.4.1); .25 A or .125 A fuse may be used in accordance with
method 1040 of MIL-STD-750.
13 Subgroup 2 of table I herein,
∆IRRM1 = 100 percent of initial value or +0.4 mA (pk), whichever is greater.
∆IDRM1 = 100 percent of initial value or +0.4 mA (pk), whichever is greater.
14a Required
14b Method 1071 of MIL-STD-750, condition C or D for gross leaks.
5
5 Page 
www.DataSheet4U.com
MIL-PRF-19500/108K
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order
(see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel
need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are
maintained by the Inventory Control Point's packaging activities within the Military Service or Defense Agency, or
within the Military Service’s system commands. Packaging data retrieval is available from the managing Military
Department's or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible
packaging activity.
6. NOTES
(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)
6.1 Intended use. The notes specified in MIL-PRF-19500 are applicable to this specification.
6.2 Acquisition requirements. Acquisition documents should specify the following:
a. Title, number, and date of this specification.
b. Packaging requirements (see 5.1).
c. Lead finish and material (see 3.4.1 and 3.4.2).
d. Product assurance level and type designator.
6.3 Qualification. With respect to products requiring qualification, awards will be made only for products which are,
at the time of award of contract, qualified for inclusion in Qualified Manufacturers List (QML-19500) whether or not
such products have actually been so listed by that date. The attention of the contractors is called to these
requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal
Government tested for qualification in order that they may be eligible to be awarded contracts or orders for the
products covered by this specification. Information pertaining to qualification of products may be obtained from
Defense Supply Center, Columbus, ATTN: DSCC/VQE, P.O. Box 3990, Columbus, OH 43218-3990 or e-mail
6.4 Changes from previous issue. The margins of this specification are marked with asterisks to indicate where
changes from the previous issue were made. This was done as a convenience only and the Government assumes
no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the
requirements of this document based on the entire content irrespective of the marginal notations and relationship to
the last previous issue.
Custodians:
Army - CR
Navy - EC
Air Force - 11
DLA - CC
Preparing activity:
DLA - CC
(Project 5961-2006-093)
Review activities:
Army - AR, AV, MI, SM
Navy - AS, MC
Air Force - 19, 99
NOTE: The activities listed above were interested in this document as of the date of this document. Since
organizations and responsibilities can change, you should verify the currency of the information above using the
ASSIST Online database at http://assist.daps.dla.mil/ .
11
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet JANTX2N688.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| JANTX2N6800 | POWER MOSFET N-CHANNEL(BVdss=400V/ Rds(on)=1.0ohm/ Id=3.0A) |  International Rectifier |
| JANTX2N6802 | POWER MOSFET N-CHANNEL(BVdss=500V/ Rds(on)=1.5ohm/ Id=2.5A) | International Rectifier |
| JANTX2N6804 | TRANSISTORS P-CHANNEL(Vdss=-100V/ Rds(on)=0.30ohm/ Id=-11A) | International Rectifier |
| JANTX2N6804 | POWER MOSFET P-CHANNEL(BVdss=-100V/ Rds(on)=0.30ohm/ Id=-11A) | International Rectifier |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |