|
|
PDF ADNB-6031 Data sheet ( Hoja de datos )
| Número de pieza | ADNB-6031 | |
| Descripción | (ADNB-6031/2) Low Power Laser Mouse Bundles | |
| Fabricantes | Agilent | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ADNB-6031 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Agilent ADNB-6031 and ADNB-6032
Low Power Laser Mouse Bundles
Datasheet
Description
The Agilent ADNB-6031 and
ADNB-6032 low power laser
mouse bundles are the world’s
first laser-illuminated system
enabled for cordless
application. Powered by
Agilent LaserStream
technology, the mouse can
operate on many surfaces that
proved difficult for traditional
LED-based optical navigation.
Its high-performance, low
power architecture is capable
of sensing high-speed mouse
motion while prolonging
battery life, two performance
areas essential in demanding
cordless applications.
The ADNS-6030 sensor along
with the ADNS-6120 or ADNS-
6130-001 lens, ADNS-6230-001
clip and ADNV-6330 VCSEL
form a complete and compact
laser mouse tracking system.
There are no moving part,
which means high reliability
and less maintenance for the
end user. In addition,
precision optical alignment is
not required, facilitating high
volume assembly.
This document will begin with
some general information and
usage guidelines on the bundle
set, followed by individual
detailed information on ADNS-
6030 laser mouse sensor,
ADNV-6330 VCSEL, ADNS-
6120 or ADNS-6130-001 lens
and ADNS-6230-001 clip.
ADNB-6031 and ADNB-6032 Low Power Laser Mouse Bundles include:
Bundle Part Number
ADNB-6031
Part Number
ADNS-6030
ADNV-6330
ADNS-6120
ADNS-6230-001
Description
Low Power Laser Mouse Sensor
Single-Mode Vertical-Cavity Surface Emitting Laser (VCSEL)
Laser Mouse Round Lens
Laser Mouse VCSEL Assembly Clip
Bundle Part Number
ADNB-6032
Part Number
ADNS-6030
ADNV-6330
ADNS-6130-001
ADNS-6230-001
Description
Low Power Laser Mouse Sensor
Single-Mode Vertical-Cavity Surface Emitting Laser (VCSEL)
Laser Mouse Trim Lens
Laser Mouse VCSEL Assembly Clip
1 page  
www.DataSheet4U.com
Design considerations for improving
ESD Performance
For improved electrostatic
discharge performance, typical
creepage and clearance
distance are shown in the
table below. Assumption: base
plate construction as per the
Agilent supplied IGES file and
ADNS-6130-001 trim lens (or
ADNS-6120 round lens).
Typical Distance
Creepage
Clearance
Millimeters
12.0
2.1
Note that the lens material is
polycarbonate and therefore,
cyanoacrylate based adhesives
or other adhesives that may
damage the lens should NOT
be used.
Figure 4. Sectional view of PCB assembly highlighting optical mouse components
SW2
Middle Button
SW1
Right Button
9 74VHC125 5 74VHC125 2 74VHC125
U3C
10
U3B
4
7 U3A 14
1 C2
0.1
8 63
+3V
C3
1
U4
LP2950ACZ-3V
31
Vout Vin
GND
2
Vcc
C4
0.1
C5
4.7
SW3
Left Button
Vcc
C1
14 0.1
5 P1.0
VCC
21
P0.7
20 P1.1
P0.6 22
6 P1.2
P0.5 23
J1 Vcc
POWER
VBUS 1
GND 2
D+ 3
19 P1.3
8
17
P1.6
P1.7
U1
CYPRESS
CY7C63743
16 D+/SCLK
P0.4 24
4
P0.3
3
P0.2
2
P0.1
D- 4
15
D-/SDATA
R1
1.30K
7
P1.4
P1.5 18
13 XTALOUT
R2
Q2
Z-ENCODER
VCC 2
1 QA
3 QB
R3
Vcc
R4
240
11 VREG/P2.0
12 XTALIN/P2.1
VSS
P0.0 1
VPP 10
27K
27K
D2
Z-LED
9
10 16
1 NCS
2 MISO
3
SCLK
9
AGND
11
AGND
4 MOSI
5
MOTION
U2
ADNS-6030
14
NC
17 NC
GND
GND
GND
15
12
13
18 NC
6
LASER_NEN
8
XY_LASER
7
LASER_GND
C7
1
C6
0.1
C9
1
C8
0.1
Q1
NTA415IP
D1
VCSEL
C10
470p
Figure 5a. Schematic Diagram for 3-Button Scroll Wheel Corded Mouse
Notes
1. The supply and ground paths should be laid out using a star methodology.
2. Level shifting is required to interface a 5V micro-controller to the ADNS-6030. If a 3V micro-controller is used, the 74VHC125 component shown may
be omitted.
5
5 Page 
www.DataSheet4U.com
ADNS-6030
VDD
AVDD
GND
AGND
XY_LASER
Image Array
DSP
Oscillator
LASER Drive
Figure 9. Block Diagram of ADNS-6030 optical module sensor
NCS
SCLK
MOSI
MISO
MOTION
LASER_NEN
Regulatory Requirements
· Passes FCC B and
worldwide analogous
emission limits when
assembled into a mouse
with shielded cable and
following Agilent
recommendations.
· Passes IEC-1000-4-3
radiated susceptibility level
when assembled into a
mouse with shielded cable
and following Agilent
recommendations.
· Passes EN61000-4-4/IEC801-
4 EFT tests when assembled
into a mouse with shielded
cable and following Agilent
recommendations.
· UL flammability level UL94
V-0.
· Provides sufficient ESD
creepage/clearance distance
to avoid discharge up to
15kV when assembled into a
mouse according to usage
instructions above.
Absolute Maximum Ratings
Parameter
Storage Temperature
Lead Solder Temp
Symbol
TS
Supply Voltage
ESD
VDD
Input Voltage
Latchup Current
VIN
Iout
Minimum
-40
Maximum
85
260
Units
OC
OC
-0.5 3.7
2
V
kV
-0.5
VDD+0.5
V
20 mA
Notes
For 10 seconds, 1.6mm below
seating plane.
All pins, human body model MIL
883 Method 3015
All Pins
All Pins
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet ADNB-6031.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ADNB-6031 | (ADNB-6031/2) Low Power Laser Mouse Bundles | Agilent |
| ADNB-6032 | (ADNB-6031/2) Low Power Laser Mouse Bundles | Agilent |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |