|
|
PDF XR16V2752 Data sheet ( Hoja de datos )
| Número de pieza | XR16V2752 | |
| Descripción | HIGH PERFORMANCE DUART | |
| Fabricantes | Exar Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de XR16V2752 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
PRELIMINARY
XR16V2752
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
JUNE 2006
REV. P1.0.0
GENERAL DESCRIPTION
The XR16V27521 (V2752) is a high performance dual
universal asynchronous receiver and transmitter
(UART) with 64 byte TX and RX FIFOs. The device
operates from 2.25 to 3.6 volts with 5 Volt tolerant
inputs and is pin-to-pin compatible to Exar’s
ST16C2552, XR16L2552 and XR16L2752. The
V2752 register set is identical to the XR16L2752 and
is compatible to the ST16C2552 and the XR16C2852
enhanced features. It supports the Exar’s enhanced
features of programmable FIFO trigger level and
FIFO level counters, automatic hardware (RTS/CTS)
and software flow control, automatic RS-485 half
duplex direction control output and a complete
modem interface. Onboard registers provide the user
with operational status and data error flags. An
internal loopback capability allows system
diagnostics. Independent programmable baud rate
generators are provided in each channel to select
data rates up to 8 Mbps at 3.3 Volt and 8X sampling
clock. The V2752 is available in 44-pin PLCC and 32-
pin QFN packages.
NOTE: 1 Covered by U.S. Patent #5,649,122
APPLICATIONS
• Portable Appliances
• Telecommunication Network Routers
• Ethernet Network Routers
• Cellular Data Devices
• Factory Automation and Process Controls
FEATURES
• 2.25 to 3.6 Volt Operation
• 5 Volt Tolerant Inputs
• Pin-to-pin compatible to Exar’s XR16L2752
• Two independent UART channels
■ Register set compatible to XR16L2752
■ Data rate of up to 8 Mbps at at 3.3 V, and
6.25 Mbps at 2.5 V with 8X sampling rate
■ Fractional Baud Rate Generator
■ Transmit and Receive FIFOs of 64 bytes
■ Programmable TX and RX FIFO Trigger Levels
■ Transmit and Receive FIFO Level Counters
■ Automatic Hardware (RTS/CTS) Flow Control
■ Selectable Auto RTS Flow Control Hysteresis
■ Automatic Software (Xon/Xoff) Flow Control
■ Automatic RS-485 Half-duplex Direction
Control Output via RTS#
■ Wireless Infrared (IrDA 1.0) Encoder/Decoder
■ Automatic sleep mode
■ Full modem interface
• Alternate Function Register
• Device Identification and Revision
• Crystal oscillator or external clock input
• Crystal oscillator (up to 32MHz) or external clock
(up to 64MHz) input
• 44-PLCC and 32-QFN packages
FIGURE 1. XR16V2752 BLOCK DIAGRAM
A2:A0
D7:D0
IOR#
IOW#
CS#
CHSEL
INTA
INTB
TXRDYA#
TXRDYB#
MFA#
(OP2A#,
BAUDOUTA#, or
RXRDYA#)
MFB#
(OP2B#,
BAUDOUTB#, or
RXRDYB#)
Reset
8-bit Data
Bus
Interface
*5 Volt Tolerant Inputs
(Except External Clock Input)
UART Channel A
UART
Regs
BRG
64 Byte TX FIFO
TX & RX IR
ENDEC
64 Byte RX FIFO
UART Channel B
(same as Channel A)
Crystal Osc/Buffer
Modem Control Logic
2.25 V to 3.6 V VCC
GND
TXA (or TXIRA)
RXA (or RXIRA)
TXB (or TXIRB)
RXB (or RXIRB)
XTAL1
XTAL2
CTS#A/B, RI#A/B,
CD#A/B, DSR#A/B
DTR#A/B, RTS#A/B
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com
1 page  
REV. P1.0.0
Pin Description
NAME
RTSB#
32-QFN
PIN #
13
CTSB#
17
DTRB#
DSRB#
-
-
CDB#
-
RIB#
-
MFB#
-
44-PLCC
PIN #
23
28
27
29
30
31
19
PRELIMINARY
XR16V2752
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
TYPE
DESCRIPTION
O UART channel B Request-to-Send (active low) or general purpose output.
This port must be asserted prior to using auto RTS flow control, see
EFR[6], MCR[1], FCTR[1:0], EMSR[5:4] and IER[6]. For auto RS485 half-
duplex direction control, see FCTR[3] and EMSR[3].
I UART channel B Clear-to-Send (active low) or general purpose input. It
can be used for auto CTS flow control, see EFR[7], and IER[7]. This input
should be connected to VCC when not used.
O UART channel B Data-Terminal-Ready (active low) or general purpose
output. If this pin is not used, leave it unconnected.
I UART channel B Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has no
effect on the UART.
I UART channel B Carrier-Detect (active low) or general purpose input. This
input should be connected to VCC when not used. This input has no effect
on the UART.
I UART channel B Ring-Indicator (active low) or general purpose input. This
input should be connected to VCC when not used. This input has no effect
on the UART.
O Multi-Function Output Channel B. This output pin can function as the
OP2B#, BAUDOUTB#, or RXRDYB# pin. One of these output signal func-
tions can be selected by the user programmable bits 1-2 of the Alternate
Function Register (AFR). These signal functions are described as follows:
1) OP2B# - When OP2B# (active low) is selected, the MF# pin is LOW
when MCR bit-3 is set HIGH (see MCR bit-3). MCR bit-3 defaults to a logic
0 condition after a reset or power-up.
2) BAUDOUTB# - When BAUDOUTB# function is selected, the 16X Baud
rate clock output is available at this pin.
ANCILLARY SIGNALS
XTAL1
4
XTAL2
5
RESET
12
11
13
21
VCC
GND
NC
26
20
18, 19
44, 33
22, 12
-
3) RXRDYB# - RXRDYB# (active low) is intended for monitoring DMA data
transfers. See Table 2 for more details.
I Crystal or external clock input. Caution: this input is not 5V tolerant.
O Crystal or buffered clock output.
I Reset (active high) - A longer than 40 ns HIGH pulse on this pin will reset
the internal registers and all outputs. The UART transmitter output will be
held HIGH, the receiver input will be ignored and outputs are reset during
reset period (see Table 16).
Pwr 2.25 to 3.6V power supply. All input pins, except XTAL1, are 5V tolerant.
Pwr Power supply common, ground.
- No Connect.
Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain.
5
5 Page 
REV. P1.0.0
PRELIMINARY
XR16V2752
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
FIGURE 5. BAUD RATE GENERATOR
To Other
Channel
XTAL1
XTAL2
Crystal
Osc/
Buffer
Prescaler
Divide by 1
Prescaler
Divide by 4
DLL, DLM and DLD
Registers
MCR Bit-7=0
(default)
Fractional Baud
Rate Generator
Logic
16X or 8X
Sampling
Rate Clock
to Transmitter
and Receiver
MCR Bit-7=1
TABLE 5: TYPICAL DATA RATES WITH A 24 MHZ CRYSTAL OR EXTERNAL CLOCK AT 16X SAMPLING
Required
Output Data
Rate
400
2400
4800
9600
10000
19200
25000
28800
38400
50000
57600
75000
100000
115200
153600
200000
225000
230400
250000
300000
400000
460800
500000
750000
921600
1000000
DIVISOR FOR
16x Clock
(Decimal)
3750
625
312.5
156.25
150
78.125
60
52.0833
39.0625
30
26.0417
20
15
13.0208
9.7656
7.5
6.6667
6.5104
6
5
3.75
3.2552
3
2
1.6276
1.5
DIVISOR
OBTAINABLE IN
V2752
3750
625
312 8/16
156 4/16
150
78 2/16
60
52 1/16
39 1/16
30
26 1/16
20
15
13
9 12/16
7 8/16
6 11/16
6 8/16
6
5
3 12/16
3 4/16
3
2
1 10/16
1 8/16
DLM PROGRAM
VALUE (HEX)
E
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DLL PROGRAM
VALUE (HEX)
A6
71
38
9C
96
4E
3C
34
27
1E
1A
14
F
D
9
7
6
6
6
5
3
3
3
2
1
1
DLD PROGRAM
VALUE (HEX)
0
0
8
4
0
2
0
1
1
0
1
0
0
0
C
8
B
8
0
0
C
4
0
0
A
8
DATA ERROR
RATE (%)
0
0
0
0
0
0
0
0.04
0
0
0.08
0
0
0.16
0.16
0
0.31
0.16
0
0
0
0.16
0
0
0.16
0
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet XR16V2752.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| XR16V2750 | HIGH PERFORMANCE DUART | Exar Corporation |
| XR16V2751 | HIGH PERFORMANCE DUART | Exar Corporation |
| XR16V2752 | HIGH PERFORMANCE DUART | Exar Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |