|
|
PDF XR16V2550 Data sheet ( Hoja de datos )
| Número de pieza | XR16V2550 | |
| Descripción | HIGH PERFORMANCE DUART | |
| Fabricantes | Exar Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de XR16V2550 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
PRELIMINARY
XR16V2550
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
JUNE 2006
REV. P1.0.0
GENERAL DESCRIPTION
The XR16V25501 (V2550) is a high performance dual
universal asynchronous receiver and transmitter
(UART) with 16 bytes TX and RX FIFOs. The device
operates from 2.25 to 3.6 volts with 5 Volt tolerant
inputs and is pin-to-pin compatible to Exar’s
ST16C2550 and XR16C2550. The V2550 register set
is compatible to the ST16C2550 and the XR16L2550.
It supports Exar’s enhanced features of selectable
FIFO trigger level, automatic hardware (RTS/CTS)
and software flow control, and a complete modem
interface. Onboard registers provide the user with
operational status and data error flags. An internal
loopback capability allows system diagnostics.
Independent programmable baud rate generators are
provided in each channel to select data rates up to 16
Mbps at 3.3 Volt with 4X sampling clock. The V2550
is available in 48-pin TQFP and 32-pin QFN
packages.
NOTE: 1 Covered by U.S. Patent #5,649,122
APPLICATIONS
• Portable Appliances
• Telecommunication Network Routers
• Ethernet Network Routers
• Cellular Data Devices
• Factory Automation and Process Controls
FEATURES
• 2.25 to 3.6 Volt Operation
• 5 Volt Tolerant Inputs
• Pin-to-pin compatible to ST16C2550, XR16C2550
and XR16L2550 in the 48-TQFP package
• Two independent UART channels
■ Register set compatible to XR16L2550
■ Data rate of up to 16 Mbps at 3.3 V, and 12.5
Mbps at 2.5 V with 4X sampling rate
■ Fractional Baud Rate Generator
■ Transmit and Receive FIFOs of 16 bytes
■ Selectable TX and RX FIFO Trigger Levels
■ Automatic Hardware (RTS/CTS) Flow Control
■ Automatic Software (Xon/Xoff) Flow Control
■ Wireless Infrared (IrDA 1.0) Encoder/Decoder
■ Automatic sleep mode
■ Full modem interface
• Device Identification and Revision
• Crystal oscillator (up to 32MHz) or external clock
(up to 64MHz) input
• 48-TQFP and 32-QFN packages
FIGURE 1. XR16V2550 BLOCK DIAGRAM
A2:A0
D7:D0
IOR#
IOW#
CSA#
CSB#
INTA
INTB
TXRDYA#
TXRDYB#
RXRDYA#
RXRDYB#
Reset
8-bit Data
Bus
Interface
* 5 Volt Tolerant Inputs
UART Channel A
UART
Regs
BRG
16 Byte TX FIFO
TX & RX
IR
ENDEC
16 Byte RX FIFO
UART Channel B
(same as Channel A)
Crystal Osc/Buffer
2.25 to 3.6 Volt VCC
GND
TXA, RXA, DTRA#,
DSRA#, RTSA#,
DTSA#, CDA#, RIA#,
OP2A#
TXB, RXB, DTRB#,
DSRB#, RTSB#,
CTSB#, CDB#, RIB#,
OP2B#
XTAL1
XTAL2
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com
1 page  
REV. P1.0.0
Pin Description
PRELIMINARY
XR16V2550
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
NAME
RTSB#
32-QFN
PIN #
15
CTSB#
16
DTRB#
DSRB#
-
-
CDB#
-
RIB#
-
OP2B#
-
ANCILLARY SIGNALS
XTAL1
10
XTAL2
11
RESET
24
VCC
GND
NC
26
13
9, 17
48-TQFP
PIN #
22
23
35
20
16
21
9
TYPE
DESCRIPTION
O UART channel B Request-to-Send (active low) or general purpose out-
put. This port must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1], and IER[6].
I UART channel B Clear-to-Send (active low) or general purpose input.
It can be used for auto CTS flow control, see EFR[7], and IER[7]. This
input should be connected to VCC when not used.
O UART channel B Data-Terminal-Ready (active low) or general purpose
output. If it is not used, leave it unconnected.
I UART channel B Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
I UART channel B Carrier-Detect (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
I UART channel B Ring-Indicator (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
O Output Port 2 Channel B - The output state is defined by the user and
through the software setting of MCR[3]. INTB is set to the active mode
and OP2B# output LOW when MCR[3] is set to a logic 1. INTB is set to
the three state mode and OP2B# output HIGH when MCR[3] is set to a
logic 0. See MCR[3]. If INTB is used, this output should not be used as
a general output else it will disturb the INTB output functionality.
13
14
36
42
17
12, 24, 25,
37
I Crystal or external clock input.
O Crystal or buffered clock output.
I Reset (active high) - A longer than 40 ns HIGH pulse on this pin will
reset the internal registers and all outputs. The UART transmitter output
will be held HIGH, the receiver input will be ignored and outputs are
reset during reset period (see Table 15).
Pwr 2.25V to 3.6V power supply. All input pins are 5V tolerant.
Pwr Power supply common, ground.
No Connection.
Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain.
5
5 Page 
REV. P1.0.0
PRELIMINARY
XR16V2550
HIGH PERFORMANCE DUART WITH 16-BYTE FIFO
FIGURE 5. BAUD RATE GENERATOR
To Other
Channel
XTAL1
XTAL2
Crystal
Osc/
Buffer
Prescaler
Divide by 1
Prescaler
Divide by 4
DLL, DLM and DLD
Registers
MCR Bit-7=0
(default)
Fractional Baud
Rate Generator
Logic
16X or 8X or 4X
Sampling
Rate Clock
to Transmitter
and Receiver
MCR Bit-7=1
TABLE 5: TYPICAL DATA RATES WITH A 24 MHZ CRYSTAL OR EXTERNAL CLOCK AT 16X SAMPLING
Required
Output Data
Rate
400
2400
4800
9600
10000
19200
25000
28800
38400
50000
57600
75000
100000
115200
153600
200000
225000
230400
250000
300000
400000
460800
500000
750000
921600
1000000
DIVISOR FOR 16x
Clock
(Decimal)
3750
625
312.5
156.25
150
78.125
60
52.0833
39.0625
30
26.0417
20
15
13.0208
9.7656
7.5
6.6667
6.5104
6
5
3.75
3.2552
3
2
1.6276
1.5
DIVISOR
OBTAINABLE IN
V2550
3750
625
312 8/16
156 4/16
150
78 2/16
60
52 1/16
39 1/16
30
26 1/16
20
15
13
9 12/16
7 8/16
6 11/16
6 8/16
6
5
3 12/16
3 4/16
3
2
1 10/16
1 8/16
DLM PROGRAM
VALUE (HEX)
E
2
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DLL PROGRAM DLD PROGRAM DATA ERROR
VALUE (HEX) VALUE (HEX)
RATE (%)
A6 0 0
71 0 0
38 8 0
9C 4 0
96 0 0
4E 2 0
3C 0 0
34 1 0.04
27 1 0
1E 0 0
1A 1 0.08
14 0 0
F 00
D 0 0.16
9 C 0.16
7 80
6 B 0.31
6 8 0.16
6 00
5 00
3 C0
3 4 0.16
3 00
2 00
1 A 0.16
1 80
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet XR16V2550.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| XR16V2550 | HIGH PERFORMANCE DUART | Exar Corporation |
| XR16V2551 | HIGH PERFORMANCE DUART | Exar Corporation |
| XR16V2552 | HIGH PERFORMANCE DUART | Exar Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |