|
|
PDF LM2457 Data sheet ( Hoja de datos )
| Número de pieza | LM2457 | |
| Descripción | Monolithic Triple 7.5nS CRT Driver | |
| Fabricantes | National Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LM2457 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
October 2000
LM2457
Monolithic Triple 7.5nS CRT Driver With Integrated
Clamp and G1 Blanking
General Description
The LM2457 driver is an integrated high voltage triple CRT
driver circuit designed for use in color monitor applications.
The input signal interface to the IC is a multiplexed signal
containing both clamp and video signal information, relative
to an external 1.7 VDC reference.
The IC contains three high gain, differential input, high input
impedance, wide band amplifiers which directly drive the
RGB cathodes of a CRT. Each channel has its gain internally
set to -52 and can drive CRT capacitive loads as well as
resistive loads present in other applications, limited only by
the package’s power dissipation.
Integrated with the driver is a triple video clamp circuit for DC
recovery of each of the AC coupled video outputs. The DC
clamp circuit amplifies the clamp signal that is multiplexed on
the video signal input. The DC clamp amplifiers are high
gain, differential input, high input impedance amplifiers, set-
ting a low impedance DC level at the clamp output which can
be used to restore the DC level of the cathode drive. Each
channel has a gain that is internally set to +75.
Also integrated within the package is a 43Vp-p vertical blank-
ing driver that is designed to drive the vertical retrace blank-
ing signal to the G1. This is a current limited, low impedance
output capable of driving normal G1 decoupling capaci-
tances via an external resistor.
The output of the G1 driver can also be used to drive a
voltage boost capacitor (22uF). When connected between
the G1 drive output and the 120v supply input pin, a 120v
boost supply is achieved which can be used to drive the
internal DC clamp circuit, thereby eliminating the require-
ment for a 120V clamp supply.
The IC is packaged in an industry standard 15 lead TO-220
molded plastic power package.
Features
n 7.5ns low power driver
n Three integrated active clamp circuits
n Integrated 120V supply and G1 vertical blank drive
circuit
n Multiplexed signal interface to LM125X OSD Pre-amp
minimizes pin count while increasing functionality
n External System voltage reference
n Convenient TO-220 staggered lead package
Recommended Applications
n 1024 x 768 Resolution displays up to 85Hz refresh
n Pixel clock frequencies up to 95MHz
n Monitor requiring horizontal video blanking
Block Diagram
Package Pinout
DS101379-1
FIGURE 1. LM2457 Block Diagram
© 2000 National Semiconductor Corporation DS101379
DS101379-2
FIGURE 2. LM2457 Package Pinout
Order Number LM2457TA
www.national.com
1 page  
www.DataSheet4U.com
DC CLAMP Electrical Characteristic Targets and Limits (See Figure 11 for Test Circuit)
Unless otherwise noted: VCC1 = +80V, VCC2 = 120V, VBB = +8V, VIN = 1.4VDC, TC = 50˚C, VREF = 1.735V, SW1 open.
HEATSINK MUST BE GROUNDED.
Symbol
Parameter
Conditions
ICC2
VOUT
AVTYP
LETYP
VCC2 Supply Current
Typical DC Output Voltage
Typical DC Voltage Gain
Typical Linearity Error
All Channel, No AC input signal,
VIN = 1.25V
No AC Input Signal, VIN = 1.4V
No AC Input Signal
No AC Input Signal (Note 6)
Note 6: Linearity Error is the variation in DC gain from VIN = 1.0V to VIN = 1.5V.
Min Typ Max Units
2.4 mA
95 VDC
75
2%
Clamp Amplifier Test Circuit
FIGURE 11. Test Circuit (One Channel)
DS101379-11
Figure 11 shows the test circuit for evaluation of the LM2457 clamp amplifier. A high impedance VM (>100 MΩ) is used for DC
measurements at the outputs.
DS101379-12
FIGURE 12. Clamp Circuit VO vs. VIN
5
www.national.com
5 Page 
www.DataSheet4U.com
Application Hints (Continued)
FIGURE 18. LM1253A/245X Reference Design Schematic (continued)
DS101379-16
11 www.national.com
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet LM2457.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LM2450 | LM2450 220V Monolithic Triple Channel 7 MHz DC Coupled CRT DTV Driver (Rev. D) |  Texas Instruments |
| LM2450 | 220V Monolithic Triple Channel 7 MHz DC Coupled CRT DTV Driver | National Semiconductor |
| LM2451 | LM2451 220V Monolithic Triple Channel 12 MHz DC Coupled CRT DTV Driver (Rev. I) | Texas Instruments |
| LM2451 | 220V Monolithic Triple Channel 12 MHz DC Coupled CRT DTV Driver | National Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |