|
|
PDF M57962K Data sheet ( Hoja de datos )
| Número de pieza | M57962K | |
| Descripción | Hybrid Integrated Circuit | |
| Fabricantes | Powerex Power Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de M57962K (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272
M57962K
Gate Driver
www.DataSheet4U.com
Outline Drawing
51 MAX
27 MAX
2.54
14
0.5+0.15/-0.1
6.5 MAX
4.5p1.5
0.25+0.2/-0.1
3 MAX
12.5
MAX
1
10
MAX
7.5 MAX
Block Diagram
LATCH
DETECT
CIRCUIT
14
TIMER &
RESET
CIRCUIT
INTERFACE
OPTO-COUPLER
1807
13
GATE SHUT-
DOWN
CIRCUIT
4 VCC
2 CONTROL PIN FOR ttrip
1 DETECT PIN
5 VO
8 FAULT OUTPUT
6 VEE
3 , 7 – NC
Hybrid Integrated Circuit
For Driving IGBT Modules
Description:
M57962K is a hybrid integrated
circuit designed to provide
optimum gate drive for IGBT
modules. This device provides
high current optically isolated gate
drive with a large output voltage
swing. The driver also provides
short circuit protection based on
desaturation detection.
Features:
£ Electrical Isolation between
input and output with
opto-couplers.
(Viso = 3750VRMS for 1 min.)
£ Two supply drive topology
£ Built in short circuit protection
circuit with a pin for fault output
£ TTL compatible input interface
Application:
To drive IGBT modules for general
industrial use apparatus.
Recommended Modules:
VCES = 600V Series
(up to 600A Class)
VCES = 1200V Series
(up to 400A Class)
VCES = 1700V Series
(up to 400A Class)
11/06
1 page  
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272
M57962K
Hybrid IC for IGBT Gate Driver
General Description
The M57962K is a hybrid integrated circuit designed
to provide gate drive for high power IGBT modules.
This circuit has been optimized for use with Powerex
1700V IGBT modules. However, the output charac-
teristics are compatible with most MOS gated power
devices. The M57962K features a compact single-in-
line package design. The upright mounting minimizes
required printed circuit board space to allow efficient
and flexible layout. The M57962K converts logic level
control signals into fully isolated +15V/-8V gate drive
with up to 5A of peak drive current. Control signal
isolation is provided by an integrated high speed opto-
coupler. Short circuit protection is provided by means
of destauration detection.
Short Circuit Protection
Figure 1 shows a block diagram of a typical desatura-
tion detector. In this circuit, a high voltage fast recovery
diode (D1) is connected to the IGBT’s collector to moni-
tor the collector to emitter voltage. When the IGBT is
in the off state, VCE is high and D1 is reverse biased.
With D1 off the (+) input of the comparator is pulled up
to the positive gate drive power supply (V+) which is
normally +15V. When the IGBT turns on, the com-
parators (+) input is pulled down by D1 to the IGBT’s
VCE(sat). The (-) input of the comparator is supplied with
a fixed voltage (VTRIP). During a normal on-state con-
dition the comparator’s (+) input will be less than VTRIP
and it’s output will be low. During a normal off-state
condition the comparator’s (+) input will be larger than
V+
INPUT
DELAY
ttrip
+
COMPARE
D1
Vtrip
AND
SHUTDOWN
GATE
DRIVE
RG
G
IGBT
MODULE
C
E
Figure 1. Desaturation Detector
E
VTRIP and it’s output will be high. If the IGBT turns on
into a short circuit, the high current will cause the IGBT’s
collector-emitter voltage to rise above VTRIP even
though the gate of the IGBT is being driven on. This
abnormal presence of high VCE when the IGBT is
supposed to be on is often called desaturation.
Desaturation can be detected by a logical AND of the
driver’s input signal and the comparator output. When
the output of the AND goes high a short circuit is
indicated. The output of the AND can be used to com-
mand the IGBT to shut down in order to protect it from
the short circuit. A delay (tTRIP) must be provided
after the comparator output to allow for the normal
turn on time of the IGBT. The tTRIP delay is set so that
the IGBTs Vce has enough time to fall below VTRIP
during normal turn on switching. If tTRIP is set too short,
erroneous desaturation detection will occur. The maxi-
mum allowable tTRIP delay is limited by the IGBT’s
short circuit withstanding capability. In typical applica-
tions using Powerex IGBT modules the recommended
limit is 10μs.
Operation of the M57962K Desaturation Detector
The Powerex M57962K incorporates short circuit
protection using desaturation detection as described
above. A flow chart for the logical operation of the
short-circuit protection is shown in Figure 2. When a
desaturation is detected the hybrid gate driver performs
a soft shut down of the IGBT and starts a timed (ttimer)
1.5ms lock out. The soft turn-off helps to limit the tran-
sient voltage that may be generated while interrupt-
ing the large short circuit current flowing in the IGBT.
During the lock out the driver pulls Pin 8 low to indicate
the fault status. Normal operation of the driver will
resume after the lock-out time has expired and the
control input signal returns to its off state.
Adjustment of Trip Time
The M57962K has a default short-circuit detection
time delay (tTRIP) of approximately 2.5μs. This will
prevent erroneous detection of short-circuit conditions
as long as the series gate resistance (RG) is near the
minimum recommended value for the module being
used. The 2.5μs delay is appropriate for most applica-
tions so adjustment will not be necessary. However, in
some low frequency applications it may be desirable
to use a larger series gate resistor to slow the switch-
ing of the IGBT, reduce noise, and limit turn-off tran-
sient voltages. When RG is increased, the switching
11/06
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet M57962K.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| M57962 | HYBRID IC FOR DRIVING IGBT MODULES |  Mitsubishi |
| M57962AL | LGBT IC |  ETC |
| M57962AL-01 | LGBT IC | ETC |
| M57962CL-01 | M57962CL-01 | ETC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |