|
|
PDF XR1004 Data sheet ( Hoja de datos )
| Número de pieza | XR1004 | |
| Descripción | GaAs MMIC Receiver | |
| Fabricantes | Mimix Broadband | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de XR1004 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
30.0-46.0 GHz GaAs MMIC
Receiver
May 2005 - Rev 13-May-05
Features
Sub-harmonic Receiver
Chip Device Layout
R1004
Integrated LNA, LO Doubler/Buffer, Image Reject Mixer
+4.0 dBm Input Third Order Intercept (IIP3)
+2.0 dBm LO Drive Level
9.0 dB Conversion Gain
3.5 dB Noise Figure
18.0 dB Image Rejection
100% On-Wafer RF, DC and Noise Figure Testing
100% Visual Inspection to MIL-STD-883 Method 2010
General Description
Mimix Broadband’s 30.0-46.0 GHz GaAs MMIC receiver has a noise
figure of 3.5 dB and 18.0 dB image rejection across the band.This
Absolute Maximum Ratings
device is a three stage LNA followed by an image reject resistive
pHEMT mixer and includes an integrated LO doubler and LO buffer
amplifer.The image reject mixer eliminates the need for a bandpass
filter after the LNA to remove thermal noise at the image frequency.
Supply Voltage (Vd)
+6.0 VDC
Supply Current (Id1,2), (Id3) 110, 180 mA
Gate Bias Voltage (Vg)
+0.3 VDC
The use of integrated LO doubler and LO buffer amplifier makes the
provision of the LO easier than for fundamental mixers at these
frequencies. I and Q mixer outputs are provided and an external 90
degree hybrid is required to select the desired sideband.This MMIC
uses Mimix Broadband’s 0.15 µm GaAs PHEMT device model
Input Power (RF Pin)
Storage Temperature (Tstg)
Operating Temperature (Ta)
Channel Temperature (Tch)
+5 dBm
-65 to +165 OC
-55 to MTTF Table3
MTTF Table3
technology, and is based upon electron beam lithography to ensure
high repeatability and uniformity.The chip has surface passivation to
www.DataSheet4U.com protect and provide a rugged part with backside via holes and gold
metallization to allow either a conductive epoxy or eutectic solder die
(3) Channel temperature affects a device's MTTF. It is
recommended to keep channel temperature as low as
possible for maximum life.
attach process.This device is well suited for Millimeter-wave Point-to-
Point Radio, LMDS, SATCOM and VSAT applications.
Electrical Characteristics (Ambient Temperature T = 25o C)
Parameter
Units Min. Typ. Max.
Frequency Range (RF) Upper Side Band
Frequency Range (RF) Lower Side Band
Frequency Range (LO)
Frequency Range (IF)
Input Return Loss RF (S11)
Small Signal Conversion Gain RF/IF (S21)2
LO Input Drive (PLO)
Image Rejection2
Noise Figure (NF)2
Isolation LO/RF @ LOx1/LOx2
Input Third Order Intercept (IIP3)1,2
Drain Bias Voltage (Vd1,2,3)
Gate Bias Voltage (Vg1,2,3)
Gate Bias Voltage (Vg4,5) Mixer, Doubler
Supply Current (Id1,2) (Vd1,2=4.0, Vg=-0.3V Typical)
Supply Current (Id3) (Vd3=4.0V,Vg=-0.3V Typical)
GHz 35.0 - 46.0
GHz 30.0 - 46.0
GHz 15.5 - 25.0
GHz DC - 4.0
dB - 10.0 -
dB - 9.0 -
dBm - +2.0 -
dBc - 18.0 -
dB - 3.5 -
dB - 40.0/40.0 -
dBm - +4.0 -
VDC - +4.0 +5.5
VDC -1.2 -0.3 +0.1
VDC -1.2 -0.5 +0.1
mA -
50 100
mA - 145 165
(1) Measured using constant current.
(2) Measured using LO Input drive level of 0.0 and +2.0 dBm.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 1 of 7
Characteristic Data and Specifications are subject to change without notice. ©2005 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
1 page  
30.0-46.0 GHz GaAs MMIC
Receiver
May 2005 - Rev 13-May-05
App Note [3] USB/LSB Selection -
LSB USB
IF2 IF1
An alternate method of Selection of USB or LSB:
USB
R1004
For Upper Side Band operation (USB):
With IF1 and IF2 connected to the
direct port (0º) and coupled port (90º)
respectively as shown in the diagram,
the USB signal will reside on the
isolated port. The input port must be
loaded with 50 ohms.
For Lower Side Band operation (LSB):
With IF1 and IF2 connected to the
direct port (0º) and coupled port (90º)
respectively as shown in the diagram,
the LSB signal will reside on the input
port. The isolated port must be loaded
with 50 ohms.
LSB
In Phase Combiner
o
-90
IF2 IF1
In Phase Combiner
o
-90
IF2 IF1
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 5 of 7
Characteristic Data and Specifications are subject to change without notice. ©2005 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet XR1004.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| XR1000 | GaAs MMIC Receiver | Mimix Broadband |
| XR1001 | GaAs MMIC Receiver | Mimix Broadband |
| XR1002 | GaAs MMIC Receiver | Mimix Broadband |
| XR1002-BD | GaAs MMIC Receiver | Mimix Broadband |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |