|
|
PDF AAT2512 Data sheet ( Hoja de datos )
| Número de pieza | AAT2512 | |
| Descripción | Dual 400mA High Frequency Buck Converter | |
| Fabricantes | AAT | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AAT2512 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
AAT2512
Dual 400mA High Frequency Buck Converter
General Description
Features
SystemPower™
The AAT2512 is a member of AnalogicTech's Total
Power Management IC™ (TPMIC™) product fam-
ily. It is a dual channel synchronous buck convert-
er operating with an input voltage range of 2.7V to
5.5V, making it ideal for applications with single-
cell lithium-ion/polymer batteries.
Both regulators have independent input and
enable pins. Offered with fixed or adjustable out-
put voltages, each channel is designed to operate
with 27µA (typical) of quiescent current, allowing
for high efficiency under light load conditions.
The AAT2512 requires only three external compo-
nents (CIN, COUT, and LX) for each converter, mini-
mizing cost and real estate. Both channels are
designed to deliver 400mA of load current and
operate with a switching frequency of 1.4MHz,
reducing the size of external components.
• VIN Range: 2.7V to 5.5V
• Output Current:
— Channel 1: 400mA
— Channel 2: 400mA
• 98% Efficient Step-Down Converter
• Integrated Power Switches
• 100% Duty Cycle
• 1.4MHz Switching Frequency
• Internal Soft Start
• 150µs Typical Turn-On Time
• Over-Temperature Protection
• Current Limit Protection
• Available in TDFN33-12 Package
• -40°C to +85°C Temperature Range
Applications
The AAT2512 is available in
TDFN33 package and is rated
+85°C temperature range.
a Pb-free, 12-pin
over the -40°C to
•
•
•www.DataSheet4U.com
•
•
Cellular Phones
Digital Cameras
Handheld Instruments
Microprocessor / DSP Core/ IO Power
PDAs and Handheld Computers
Typical Application
V BAT
CIN
VIN1
LX1
VIN2
FB1
AAT2512
EN1 LX2
EN2 FB2
GND
L1
4.7µH
V OUT1
VOUT2
L2
4.7µH
4.7µF
COUT
4.7µF
2512.2006.06.1.4
1
1 page  
AAT2512
Dual 400mA High Frequency Buck Converter
Typical Characteristics
EN1 = VIN; EN2 = GND.
Efficiency vs. Load
(VOUT = 1.8V; L = 4.7μH)
100
VIN = 2.7V
90
80 VIN = 3.6V VIN = 4.2V
70
60
50
0.1
1 10 100
Output Current (mA)
1000
1.0
0.5
0.0
-0.5
-1.0
0.1
DC Regulation
(VOUT = 1.8V)
VIN = 4.2V
VIN = 3.6V
VIN = 2.7V
1 10 100 1000
Output Current (mA)
Efficiency vs. Load
(VOUT = 2.5V; L = 6.8μH)
100
VIN = 2.7V
90
80 VIN = 5.0V
VIN = 4.2V
70 VIN = 3.6V
60
50
0.1
1 10 100
Output Current (mA)
1000
1.0
0.5
0.0
-0.5
-1.0
0.1
DC Regulation
(VOUT = 2.5V)
VIN = 4.2V
VIN = 5.0V
VIN = 3.6V
VIN = 3.0V
1 10 100
Output Current (mA)
1000
Efficiency vs. Load
(VOUT = 3.3V; L = 6.8μH)
100
VIN = 3.6V
90
VIN = 4.2V
80
VIN = 5.0V
70
60
50
0.1
1 10 100
Output Current (mA)
1000
1.0
0.5
0.0
-0.5
-1.0
0.1
DC Regulation
(VOUT = 3.3V; L = 6.8µH)
VIN = 5.0V
VIN = 4.2V
VIN = 3.6V
1 10 100
Output Current (mA)
1000
2512.2006.06.1.4
5
5 Page 
AAT2512
Dual 400mA High Frequency Buck Converter
The equation below solves for input capacitor size
for both channels. It makes the worst-case
assumptions that both converters are operating at
50% duty cycle and are synchronized.
CIN =
⎛ VPP
⎝ IO1 + IO2
1
-
ESR⎞
⎠
·
4
·
FS
Because the AAT2512 channels will generally
operate at different duty cycles and are not syn-
chronized, the actual ripple will vary and be less
than the ripple (VPP) used to solve for the input
capacitor in the equation above.
Always examine the ceramic capacitor DC voltage
coefficient characteristics when selecting the prop-
er value. For example, the capacitance of a 10µF
6.3V X5R ceramic capacitor with 5V DC applied is
actually about 6µF.
The maximum input capacitor RMS current is:
⎛⎝ ⎞⎠ ⎝⎛ ⎞⎠IRMS = IO1 ·
VO1
VIN
·
⎛⎝1 -
VO1 ⎞
VIN ⎠
+ IO2 ·
VO2
VIN
·
⎛⎝1 -
VO2 ⎞
VIN ⎠
The input capacitor RMS ripple current varies with
the input and output voltage and will always be less
than or equal to half of the total DC load current of
both converters combined.
I =RMS(MAX)
I + IO1(MAX) O2(MAX)
2
This equation also makes the worst-case assump-
tion that both converters are operating at 50% duty
cycle and are synchronized. Since the converters
are not synchronized and are not both operating at
50% duty cycle, the actual RMS current will always
be less than this. Losses associated with the input
ceramic capacitor are typically minimal.
The term
VO
VIN
·
⎛⎝1 -
VO ⎞
VIN ⎠
appears in both the input
voltage ripple and input capacitor RMS current
equations. It is a maximum when VO is twice VIN.
This is why the input voltage ripple and the input
capacitor RMS current ripple are a maximum at
50% duty cycle.
2512.2006.06.1.4
The input capacitor provides a low impedance loop
for the edges of pulsed current drawn by the
AAT2512. Low ESR/ESL X7R and X5R ceramic
capacitors are ideal for this function. To minimize
the stray inductance, the capacitor should be
placed as closely as possible to the IC. This keeps
the high frequency content of the input current
localized, minimizing EMI and input voltage ripple.
The proper placement of the input capacitor (C3
and C8) can be seen in the evaluation board layout
in Figure 4. Since decoupling must be as close to
the input pins as possible, it is necessary to use
two decoupling capacitors. C3 provides the bulk
capacitance required for both converters, while C8
is a high frequency bypass capacitor for the second
channel (see C3 and C8 placement in Figure 4).
A laboratory test set-up typically consists of two
long wires running from the bench power supply to
the evaluation board input voltage pins. The induc-
tance of these wires, along with the low ESR
ceramic input capacitor, can create a high Q net-
work that may affect converter performance.
This problem often becomes apparent in the form
of excessive ringing in the output voltage during
load transients. Errors in the loop phase and gain
measurements can also result.
Since the inductance of a short printed circuit board
trace feeding the input voltage is significantly lower
than the power leads from the bench power supply,
most applications do not exhibit this problem.
In applications where the input power source lead
inductance cannot be reduced to a level that does
not affect converter performance, a high ESR tan-
talum or aluminum electrolytic capacitor should be
placed in parallel with the low ESR, ESL bypass
ceramic capacitor. This dampens the high Q net-
work and stabilizes the system.
Output Capacitor
The output capacitor limits the output ripple and
provides holdup during large load transitions. A
4.7µF to 10µF X5R or X7R ceramic capacitor typi-
cally provides sufficient bulk capacitance to stabi-
lize the output during large load transitions and has
the ESR and ESL characteristics necessary for low
output ripple.
11
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet AAT2512.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AAT2510 | Step-Down DC-DC Converter | AAT |
| AAT2511 | Step-Down DC/DC Converter | AAT |
| AAT2512 | Dual 400mA High Frequency Buck Converter | AAT |
| AAT2513 | Dual 600mA Step-Down Converter | AAT |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |