|
|
Número de pieza | NCP584 | |
Descripción | Tri-Mode 200 mA CMOS LDO Regulator | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de NCP584 (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
No Preview Available ! NCP584
Tri−Mode 200 mA CMOS
LDO Regulator with Enable
The NCP584 series of low drop out regulators are designed for
portable battery powered applications which require precise output
voltage accuracy, low supply current, and high ripple rejection.
These devices feature an enable function which lowers current
consumption significantly and are offered in the SOT23−5 package.
This series of devices have three modes. Chip Enable (CE mode),
Fast Transient Mode (FT mode), and Low Power Mode (LP mode).
Both the FT and LP mode are utilized via the ECO pin.
Features
• Low Dropout Voltage of 300 mV at 200 mA, Output Voltage = 1.0 V
200 mV at 200 mA, Output Voltage = 1.5 V
140 mV at 200 mA, Output Voltage = 3.0 V
• Excellent Line and Load Regulation
• High Output Voltage Accuracy of ±2% (±3% LP mode)
• Ultra−Low Supply Current of:
3.5 mA (LP mode, Output Voltage ≤ 1.5 V)
40 mA (FT mode)
• Excellent Power Supply Rejection Ratio
• Low Temperature Drift Coefficient on the Output Voltage
• Low Quiescent Current of 0.1 mA
• This is a Pb−Free Device*
www.DataSheet4U.com
Typical Applications
• Portable Equipment
• Hand−Held Instrumentation
• Camcorders and Cameras
ECO
http://onsemi.com
MARKING
DIAGRAM
5
1
SOT23−5
SN SUFFIX
CASE 1212
5
DEVM
1
DEV = Device Code
M = Date Code
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
ECO
Vin Vout Vin Vout
−
+
Vref
Current Limit
CE
GND CE
−
+
Vref
Current Limit
GND
Figure 1. Simplified Block Diagram for Active Low
Figure 2. Simplified Block Diagram for Active High
*For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting
Techniques Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2005
July, 2005 − Rev. 2
1
Publication Order Number:
NCP584/D
1 page NCP584
TYPICAL CHARACTERISTICS
0.83 0.83
0.82 0.82
0.81 0.81
0.80 0.80
0.79 0.79
0.78
0.77
−50
−25
Vout = 0.8 V
ECO = H
0 25 50
TEMPERATURE (°C)
75 100
Figure 15. Output Voltage vs. Temperature
0.78
0.77
−50
−25
Vout = 0.8 V
ECO = L
0 25 50
TEMPERATURE (°C)
75 100
Figure 16. Output Voltage vs. Temperature
1.53
1.52
1.51
1.50
1.49
1.48
1.47
1.46
−50
−25
0
Vout = 1.5 V
ECO = H
25 50 75 100
TEMPERATURE (°C)
Figure 17. Output Voltage vs. Temperature
1.53
1.52
1.51
1.50
1.49
1.48
1.47
1.46
−50
−25
0
Vout = 1.5 V
ECO = L
25 50 75 100
TEMPERATURE (°C)
Figure 18. Output Voltage vs. Temperature
0.6
0.5
0.4
25°C
85°C
0.3 −40°C
0.2
0.1
Vout = 0.8 V
ECO = H
0.0
0 25 50 75 100 125 150 175 200
OUTPUT CURRENT Iout (mA)
Figure 19. Dropout Voltage vs. Output Current
0.6
0.5
25°C
85°C
0.4
0.3 −40°C
0.2
0.1
0.0
0
25 50
Vout = 0.8 V
ECO = L
75 100 125 150 175 200
OUTPUT CURRENT Iout (mA)
Figure 20. Dropout Voltage vs. Output Current
http://onsemi.com
5
5 Page NCP584
APPLICATION INFORMATION
Input Decoupling
A 1.0 mF tantalum capacitor is the recommended value
to be connected between Vin and GND. For PCB layout
considerations, the traces of Vin and GND should be
sufficiently wide in order to minimize noise and prevent
unstable operation.
Output Decoupling
It is recommended to use a 2.2 mF or higher tantalum
capacitor on the Vout pin. For better performance, select a
capacitor with low Equivalent Series Resistance (ESR).
For PCB layout considerations, place the output capacitor
close to the output pin and keep the leads short as possible.
ORDERING INFORMATION
Device
Output Type / Features
Nominal
Output Voltage
Marking
Package
Shipping†
NCP584HSN09T1G
Active High,
LP and FT Mode
0.9
109
SOT23−5
3000 Tape & Reel
(Pb−Free)
NCP584HSN12T1G
Active High,
LP and FT Mode
1.2
112
SOT23−5
3000 Tape & Reel
(Pb−Free)
NCP584HSN15T1G
Active High,
LP and FT Mode
1.5
115
SOT23−5
3000 Tape & Reel
(Pb−Free)
NCP584HSN18T1G
Active High,
LP and FT Mode
1.8
118
SOT23−5
3000 Tape & Reel
(Pb−Free)
NCP584HSN26T1G
Active High,
LP and FT Mode
2.6
126
SOT23−5
3000 Tape & Reel
(Pb−Free)
NCP584HSN31T1G
Active High,
LP and FT Mode
3.1
131
SOT23−5
3000 Tape & Reel
(Pb−Free)
NCP584LSN09T1G
Active Low,
LP and FT Mode
0.9
009
SOT23−5
3000 Tape & Reel
(Pb−Free)
NCP584LSN12T1G
Active Low,
LP and FT Mode
1.2
012
SOT23−5
3000 Tape & Reel
(Pb−Free)
NCP584LSN18T1G
Active Low,
LP and FT Mode
1.8
018
SOT23−5
3000 Tape & Reel
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
http://onsemi.com
11
11 Page |
Páginas | Total 12 Páginas | |
PDF Descargar | [ Datasheet NCP584.PDF ] |
Número de pieza | Descripción | Fabricantes |
NCP580 | CMOS LDO Regulator | ON Semiconductor |
NCP5810 | Dual 1 W Output AMOLED Driver Supply | ON Semiconductor |
NCP582 | Low Noise 150 mA CMOS LDO Regulator with Enable | ON |
NCP583 | Ultra-Low Iq 150 mA CMOS LDO Regulator | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |