DataSheetWiki


DG508A fiches techniques PDF

Vishay Siliconix - (DG508A / DG509A) Single 8-Ch/Differential 4-Ch CMOS Analog Multiplexers

Numéro de référence DG508A
Description (DG508A / DG509A) Single 8-Ch/Differential 4-Ch CMOS Analog Multiplexers
Fabricant Vishay Siliconix 
Logo Vishay Siliconix 





1 Page

No Preview Available !





DG508A fiche technique
www.DataSheet4U.com
DG508A_MIL/509A_MIL
Vishay Siliconix
Single 8-Ch/Differential 4-Ch CMOS Analog Multiplexers
(Obsolete for non-hermetic. Use DG408/409 as pin-for-pin replacements.)
FEATURES
D Low On-Resistance: 240 W
D TTL and CMOS Logic Compatible
D Low Power: 30 mW
D Break-Before-Make Switching
D 44-V Power Supply Rating
D Transition Time: 600 ns
BENEFITS
D Easily Interfaced
D Low Power Consumption
D Low System Crosstalk
D Wide Analog Signal Range
APPLICATIONS
D Communication Systems
D ATE
D Data Acquisition Systems
D Audio Signal Routing and Multiplexing
D Medical Instrumentation
DESCRIPTION
The DG508A_MIL, an 8-channel single-ended analog
multiplexer, is designed to connect one of eight inputs to a
common output as determined by a 3-bit binary address (A0,
A1, A2).
The DG509A_MIL, a dual 4-channel analog multiplexer, is
designed to connect one of four differential inputs to a common
output as determined by its 2-bit binary address (A0, A1) logic.
Break-before-make switching action protects against
momentary shorting of the input signals.
enable (EN) are TTL or CMOS compatible over the full
specified operating temperature range.
Fabricated in the Vishay Siliconix Plus-40 process, the
absolute maximum voltage rating is extended to 44 V, allowing
increased operating headroom for standard "15-V signal
swings and operation with "20-V supplies. An epitaxial layer
prevents latch up.
The DG508A_MIL/509A_MIL are available in hermetic
packages. For plastic packages, use the DG408/409 as
pin-for-pin replacements.
A channel in the on state conducts current equally well in both
directions. In the off state each channel blocks voltages up to
the power supply rails, normally 30 V peak-to-peak. An enable
(EN) function allows for device selection when several
multiplexers are used All control inputs, address (AX) and
For applications requiring address data latching, the
DG528/529 is recommended. DG408/409 is recommended
for higher precision applications. For wideband/video routing
and multiplexing, the DG538A is recommended.
FUNCTIONAL BLOCK DIAGRAMS AND PIN CONFIGURATIONS
Dual-In-Line
A0 1
EN
2
V–
3
S1 4
S2 5
S3 6
S4 7
D8
16 A1
Decoders/Drivers 15 A2
GND
14
V+
13
12 S5
11 S6
10 S7
DG508A_MIL
9 S8
Top View
LCC
EN A0 NC A1 A2
Key
3 2 1 20 19
V– 4
S1 5
NC 6
S2 7
S3 8
Decoders/Drivers
18 GND
17
DG508A_MIL
16
V+
NC
15 S5
14 S6
9 10 11 12 13
S4 D NC S8 S7
Top View
Document Number: 70067
S-00405—Rev. C, 21-Feb-00
www.vishay.com S FaxBack 408-970-5600
5-1

PagesPages 11
Télécharger [ DG508A ]


Fiche technique recommandé

No Description détaillée Fabricant
DG508A Single 8-Channel/Differential 4-Channel CMOS Analog Multiplexers TEMIC
TEMIC
DG508A Monolithic CMOS Analog Multiplexers Maxim Integrated
Maxim Integrated
DG508A CMOS Analog Multiplexers Intersil Corporation
Intersil Corporation
DG508A (DG508A / DG509A) Single 8-Ch/Differential 4-Ch CMOS Analog Multiplexers Vishay Siliconix
Vishay Siliconix

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche