|
|
PDF LA4632 Data sheet ( Hoja de datos )
| Número de pieza | LA4632 | |
| Descripción | 10 W Two-Channel BTL AF Power Amplifier | |
| Fabricantes | Sanyo Semicon Device | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LA4632 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Ordering number : ENN8178
SANYO Semiconductors
DATA SHEET
LA4632
Monolithic Linear IC
10 W Two-Channel BTL AF Power
Amplifier for Audio Applications
Overview
The LA4632 is a pin compatible version of the LA4631 (5 W × two channel single ended type) BTL power amplifier
IC. The LA4632's pin compatibility makes it possible to share a common printed circuit board among a series of end
products differentiated by power rank. Note that the LA4631 has a pin 13, and that it is necessary to provide a hole for
this pin if the same printed circuit board is to be shared. Also, some of the external components used differ. The
LA4632 provides a full complement of built-in protection circuits, including protection against shorting to the power
supply, shorting to ground, load shorting, and excessive temperatures.
Functions and Applications
• Two-channel BTL power amplifier for audio applications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Maximum output current
Allowable power dissipation
Maximum junction temperature
Operating temperature
Storage temperature
Symbol
VCC max
IO peak
Pd max
Tj max
Topr
Tstg
Conditions
With no input signal
Per channel
With an infinitely large heat sink
Rated value
24
2.5
25
150
–20 to +75
–40 to +150
Unit
V
A
W
°C
°C
°C
Operating Characteristics at Ta = 25°C
Parameter
Recommended supply voltage
Recommended load resistance range
Allowable operating supply voltage range *1
Symbol
VCC
RL op
VCC op
Conditions
When RL = 8 Ω
When RL = 6 Ω
When RL = 4 Ω
Rated value
13
4 to 8
5.5 to 20
5.5 to 17
5.5 to 13
Unit
V
Ω
V
V
V
Caution: VCC, RL, and the output level must be set for the size of the heat sink used so that the Pd max range is not exceeded.
*1. When both channels are operating such that IOpeak = 1.0 A per channel is exceeded.
If the IC is operated such that IOpeak = 1.0 A per channel is not exceeded, the IC can be used in the range 5.5 to 20 V (in the ranges where Pd max is
not exceeded) with a load of RL = 4 to 8 Ω.
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
33105TN (OT) No.8178-1/8
1 page  
LA4632
Pin 6 IC internal equivalent circuit
When an voltage of +5 V is applied to the mute pin through the
external 15 kΩ resistor, the pin 6 voltage becomes about 1.85 V. (The
15kΩ Imute
+5V
Mute pin applied
voltage
6
2kΩ
muting function activation level in the specifications is 1.7 V
minimum.) The pin 6 influx current (Imute) at this time will be
roughly 210 µA.
Although it is possible to change the mute pin applied voltage or the
values of the mute pin external components, if the pin 6 voltage (and
pin 6 influx current) is too high, or if the pin 6 external component
time constant is too short, the amplitude of impulse noise in the
system may rise. This phenomenon must be taken into account when
Other items
designing this circuit.
Standby function
Pin 5 IC internal equivalent circuit
Use ISTB = up to 500µA
as an initial target.
RSTB
15kΩ
5
2VBE
Standby pin
applied voltage
The IC's pin 5 is a standby pin. The amplifier is turned on when the
voltage applied to this pin is about 2 V or higher. (The value in the
specifications is 2.5 V minimum.) If a voltage of +5 V is directly
applied to the standby pin, the pin 5 influx current will be about 230
µA.
ISTB =
5 V – 2 VBE (about 1.55 V)
15 kΩ
= 230 µA
If a voltage that exceeds the upper limit voltage given in the
specifications (10 V) is applied as the standby pin voltage, calculate a
value for an external resistor RSTB from the following formula so that
the pin 5 influx current does not increase excessively (use a value of under about 500 µA as the initial target value).
Usage Notes
RSTB =
Applied voltage - 2VBE (about 1.55 V)
ISTB (Under 500 µA)
– 15 kΩ
Notes on the Maximum Ratings
If this IC is used in the vicinity of the maximum ratings, even the slightest fluctuations in the operating conditions could
cause those ratings to be exceeded, making the destruction of the device possible. Applications must be designed with
adequate margins in the supply voltage and other parameters so that the devices is always used in ranges that do not
exceed the maximum ratings.
Notes on Protection Circuits
While the LA4632 provides a full complement of built-in protection circuits, care is required in their use. In particular,
be careful not to inadvertently short IC pins to each other.
[Notes on the short to power, short to ground, and load shorting protection circuit]
• This protection circuit operates when an abnormal short such as a short to power (a short between an output and
VCC), a short to ground (a short between an output and ground), or a load short (a short between the output ± sides)
occurs. Although this circuit may not operate when the VCC voltage is under about 9 V, the thermal protection
circuit is thought adequate to protect the IC in that case.
• This protection circuit is the type that continues to operate while the above listed short state continues and recovers
automatically as soon as the abnormality is resolved. However, there are cases where, depending on the operating
conditions, the protection circuit locks and the protection operation continues. In these cases, the protection circuit
can be cleared by switching to standby mode or cutting and reapplying power.
• Note that if the output is shorted to power in the state where the IC is in the standby state (amplifier operation is
turned off) and VCC is over about 20 V, an offset may occur between the plus and minus outputs. If a load is
connected in this state, current may flow in through the load and the IC may be destroyed.
• In the following usage conditions, a symptom in which the output audio is cut off at high outputs due to protection
circuit operation. Depending on the end product specifications, it may be necessary to check for this phenomenon.
• Situations where both channels are operating in a manner that the IOPeak per channel exceeds 1 A at low RL (high
loads) and high VCC (The higher the chip temperature the easier it is for this phenomenon to occur.)
The "Allowable operating supply voltage range (VCC op)" item in the operating conditions specifications provides
specific target operating conditions so that the above phenomenon will not occur under severe usage conditions
(high temperatures, high outputs. (See the different VCC op ranges for different RL values.)
No.8178-5/8
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet LA4632.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LA4630N | 9V/12V 3-Dimension Power IC for Radio Cassette Recorders |  Sanyo |
| LA4631 | 5 W Two-Channel AF Power Amplifier |  SANYO Semiconductors |
| LA4632 | 10 W Two-Channel BTL AF Power Amplifier | Sanyo Semicon Device |
| LA4635 | 2-Channel BTL AF Power Amplifier | Sanyo |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |