DataSheetWiki


OP268FPS fiches techniques PDF

OPTEK Technologies - Plastic Point Source

Numéro de référence OP268FPS
Description Plastic Point Source
Fabricant OPTEK Technologies 
Logo OPTEK Technologies 





1 Page

No Preview Available !





OP268FPS fiche technique
www.DataSheet4U.com
Product Bulletin OP268FPS
November 2000
Plastic Point Source Infrared Emitting Diode
Type OP268FPS
Features
Point source irradiance pattern
Flat lensed for wide radiation angle
Easily stackable on 0.100”(2.54 mm)
hole centers
Description
The OP268FPS contains an 850 nm
gallium aluminum arsenide infrared
emitting diode molded in an
“end-looking”miniature black package.
This device has a wide radiation angle
due to its flat emitting surface. The point
source GaAIAs IRED emits photons from
a 0.004”diameter area centered with the
optical centerline. Small size and 0.100”
(2.54 mm) lead spacing allow
considerable design flexibility.
Absolute Maximum Ratings (TA = 25o C unless otherwise noted)
Reverse Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 V
Continuous Forward Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Peak Forward Current (2 µs pulse width, 0.1% duty cycle). . . . . . . . . . . . . . . . . . 1.0 A
Storage and Operating Temperature Range . . . . . . . . . . . . . . . . . . . -40°C to +100°C
Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 sec. with soldering
iron] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C (1)
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW(2)
NOTES:
(1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow
soldering. Maximum 20 grams force may be applied to the leads when soldering.
(2) Derate linearly 1.33 mW/°C above 25°C.
(3) Ee(APT) is a measurement of the average apertured radiant energy incident upon a sensing
area 0.081”(2.06 mm) in diameter, perpendicular to and centered on the mechanical axis of
the “emitting surface”and 0.400”(10.16 mm) from the measurement surface. Ee(APT) is not
necessarily uniform within the measured area.
The stable VF vs. Temperature
characteristic make them ideal for
applications where voltage is limited
(such as battery operation).
The low tr/tf make them ideal for high
speed operation.
Optek Technology, Inc.
1215 W. Crosby Road
Carrollton, Texas 75006
11
(972) 323-2200
Fax (972) 323-2396

PagesPages 2
Télécharger [ OP268FPS ]


Fiche technique recommandé

No Description détaillée Fabricant
OP268FPS Plastic Point Source OPTEK Technologies
OPTEK Technologies

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche