|
|
PDF EM78P569 Data sheet ( Hoja de datos )
| Número de pieza | EM78P569 | |
| Descripción | 8-BIT OTP MICRO-CONTROLLER | |
| Fabricantes | ELAN Microelectronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de EM78P569 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
EM78P569
8-BIT OTP MICRO-CONTROLLER
Version V4.4
ELAN MICROELECTRONICS CORP.
No. 12, Innovation 1st RD., Science-Based Industrial Park
Hsin Chu City, Taiwan, R.O.C.
TEL: (03) 5639977
FAX: (03) 5630118
1 page  
LCD
Common driver pins : 4
Segment driver pins : 32
1/3 bias
1/4 duty, 1/2 duty
16 Level LCD contrast control by software
Multiplier
8 x 8 multiplier
PACKAGE
100-pin QFP
73-pin die
III. Application
Communication or general product.
EM78P569
8-bit OTP Micro-controller
__________________________________________________________________________________________________________________________________________________________________
* This specification is subject to be changed without notice.
8/19/2004 V4.4
5 Page 
EM78P569
8-bit OTP Micro-controller
0B PortB I/O control
0C PortC I/O control
0D
0E Interrupt mask
0F Interrupt mask
10
:
1F
20
:
3F
ADC control
Port5,8,B,C switch
Clock source(CN1,CN2)
Prescaler(CN1,CN2)
VII.2 Operational Register Detail Description
R0 (Indirect Addressing Register)
R0 is not a physically implemented register. It is used as indirect addressing pointer. Any instruction using R0
as register actually accesses data pointed by the RAM Select Register (R4).
Example:
Mov A, @0x20
;store a address at R4 for indirect addressing
Mov 0x04, A
Mov A, @0xAA ;write data 0xAA to R20 at bank0 through R0
Mov 0x00, A
R1 (TCC)
TCC data buffer. Increased by 16.384KHz or by the instruction cycle clock (controlled by CONT register).
Written and read by the program as any other register.
R2 (Program Counter)
The structure is depicted in Fig.3.
Generates 16k × 13 on-chip PROGRAM OTP-ROM addresses to the relative programming instruction codes.
"JMP" instruction allows the direct loading of the low 10 program counter bits.
"CALL" instruction loads the low 10 bits of the PC, PC+1, and then push into the stack.
"RET'' ("RETL k", "RETI") instruction loads the program counter with the contents at the top of stack.
"MOV R2, A" allows the loading of an address from the A register to the PC, and the ninth and tenth bits are
cleared to "0''.
"ADD R2,A" allows a relative address be added to the current PC, and contents of the ninth and tenth bits are
cleared to "0''.
"TBL" allows a relative address added to the current PC, and contents of the ninth and tenth bits don't change.
The most significant bit (A10~A13) will be loaded with the contents of bit PS0~PS3 in the status register (R5
PAGE0) upon the execution of a "JMP'', "CALL'', "ADD R2, A'', or "MOV R2, A'' instruction.
If an interrupt is triggered, PROGRAM ROM will jump to address 0x08 at page0. The CPU will store ACC,
R3 status and R5 PAGE automatically, and they will be restored after instruction RETI.
__________________________________________________________________________________________________________________________________________________________________
* This specification is subject to be changed without notice.
8/19/2004 V4.4
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet EM78P569.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| EM78P567 | 8-BIT OTP MICRO-CONTROLLER | ELAN Microelectronics |
| EM78P568 | 8-BIT OTP MICRO-CONTROLLER | ELAN Microelectronics |
| EM78P569 | 8-BIT OTP MICRO-CONTROLLER | ELAN Microelectronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |