DataSheetWiki


FPF2102 fiches techniques PDF

Fairchild Semiconductor - (FPF2100 - FPF2107) IntelliMAX Advanced Load Management Products

Numéro de référence FPF2102
Description (FPF2100 - FPF2107) IntelliMAX Advanced Load Management Products
Fabricant Fairchild Semiconductor 
Logo Fairchild Semiconductor 





1 Page

No Preview Available !





FPF2102 fiche technique
www.DataSheet4U.com
May 2005
FPF2100-FPF2107
IntelliMAX™ Advanced Load Management Products
Features
1.8 to 5.5V Input Voltage Range
Controlled Turn-On
200mA and 400mA Current Limit Options
Undervoltage Lockout
Thermal Shutdown
<1uA Shutdown Current
Auto restart
Fast Current limit Response Time
3us to Moderate Over Currents
20ns to Hard Shorts
Fault Blanking
Applications
PDAs
Cell Phones
GPS Devices
MP3 Players
Digital Cameras
Peripheral Ports
Hot Swap Supplies
Typical Application Circuit
General Description
The FPF2100 through FPF2107 is a family of load switches
which provide full protection to systems and loads which may
encounter large current conditions. These devices contain a
0.125current-limited P-channel MOSFET which can operate
over an input voltage range of 1.8-5.5V. Switch control is by a
logic input (ON) capable of interfacing directly with low voltage
control signals. Each part contains thermal shutdown protection
which shuts off the switch to prevent damage to the part when a
continuous over-current condition causes excessive heating.
When the switch current reaches the current limit, the part
operates in a constant-current mode to prohibit excessive
currents from causing damage. For the FPF2100-FPF2102 and
FPF2104-FPF2106, if the constant current condition still
persists after 10ms, these parts will shut off the switch and pull
the fault signal pin (FLAGB) low. The FPF2100, FPF2101,
FPF2104 and FPF2105, have an auto-restart feature which will
turn the switch on again after 160ms if the ON pin is still active.
The FPF2102 and FPF2106 do not have this auto-restart
feature so the switch will remain off until the ON pin is cycled.
For the FPF2103 and FPF2107, a current limit condition will
immediately pull the fault signal pin low and the part will remain
in the constant-current mode until the switch current falls below
the current limit. For the FPF2100 through FPF2103, the
minimum current limit is 200mA while that for the FPF2104
through FPF2107 is 400mA.
These parts are available in a space-saving 5 pin SOT23
package.
OFF ON
VIN VOUT
FPF2100 - FPF2107
ON FLAGB
GND
TO LOAD
©2005 Fairchild Semiconductor Corporation
FPF2100-FPF2107 Rev. D2
1
www.fairchildsemi.com

PagesPages 12
Télécharger [ FPF2102 ]


Fiche technique recommandé

No Description détaillée Fabricant
FPF2100 (FPF2100 - FPF2107) IntelliMAX Advanced Load Management Products Fairchild Semiconductor
Fairchild Semiconductor
FPF2101 (FPF2100 - FPF2107) IntelliMAX Advanced Load Management Products Fairchild Semiconductor
Fairchild Semiconductor
FPF2102 (FPF2100 - FPF2107) IntelliMAX Advanced Load Management Products Fairchild Semiconductor
Fairchild Semiconductor
FPF2103 (FPF2100 - FPF2107) IntelliMAX Advanced Load Management Products Fairchild Semiconductor
Fairchild Semiconductor

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche