PDF IDTCV110J Data sheet ( Hoja de datos )

Número de pieza	IDTCV110J
Descripción	PROGRAMMABLE FLEXPC CLOCK FOR P4 PROCESSOR
Fabricantes	Integrated Device Technology
Logotipo
Hay una vista previa y un enlace de descarga de IDTCV110J (archivo pdf) en la parte inferior de esta página. Total 16 Páginas
No Preview Available ! www.DataSheet4U.com IDTCV110J PROGRAMMABLE FLEXPC CLOCK FOR P4 PROCESSOR COMMERCIALTEMPERATURERANGE PROGRAMMABLE FLEXPC CLOCK FOR P4 PROCESSOR IDTCV110J FEATURES: • One high precision PLL for CPU, SSC, and N programming • One high precision PLL for SRC/PCI/SATA, SSC, and N programming • One high precision PLL for 96MHz/48MHz • Band-gap circuit for differential outputs • Support spread spectrum modulation, down spread 0.5% • Support SMBus block read/write, index read/write • Selectable output strength for REF • Allows for CPU frequency to change to a higher frequency for maximum system computing power • Available in SSOP package DESCRIPTION: IDTCV110J is a 56 pin clock device. The CPU output buffer is designed to support up to 400MHz processor. This chip has three PLLs inside for CPU/ SRC/PCI, SATA, and 48MHz/DOT96 IO clocks. One dedicated PLL for Serial ATA clock provides high accuracy frequency. This device also implements Band-gap referenced IREF to reduce the impact of VDD variation on differential outputs, which can provide more robust system performance. Static PLL frequency divide error can be as low as 36 ppm, worse case 114 ppm, providing high accuracy output clock. Each CPU/SRC/PCI, SATA clock has its own Spread Spectrum selection, which allows for isolated changes instead of affecting other clock groups. OUTPUTS: • 20.7V current –mode differential CPU CLK pair • 60.7V current –mode differential SRC CLK pair, one dedicated KEY SPECIFICATION: for SATA • CPU/SRC CLK cycle to cycle jitter < 85ps • One CPU_ITP/SRC selectable CLK pair • SATA CLK cycle to cycle jitter < 85ps • 9PCI, 3 free running, 33.3MHz • PCI CLK cycle to cycle jitter < 250ps • 196MHz,148MHz • Static PLL frequency divide error < 114 ppm • 1REF DataSheet•4USt.actoicmPLL frequency divide error for 48MHz < 5 ppm FUNCTIONAL BLOCK DIAGRAM DataShee X1 X2 SDATA SCLK XTAL Osc Amp SM Bus Controller VTT_PWRGD#/PD FSA.B.C Control Logic PLL1 SSC N Programmable CPU CLK Output Buffers Stop Logic IREF ITP_EN PLL2 SSC N Programmable SRC CLK Output Buffer Stop Logic IREF PLL3 48MHz/96MHz Output BUffer DataSheet4U.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. COMMERCIAL TEMPERATURE RANGE © 2004 Integrated Device Technology, Inc. 1 CPU[1:0] CPU_ITP/SRC7 REF SRC[6:1] PCI[5:0], PCIF[2:0] 48MHz DOT96 MAY 2004 DSC-6507/12 1 page www.DataSheet4U.com IDTCV110J PROGRAMMABLE FLEXPC CLOCK FOR P4 PROCESSOR COMMERCIALTEMPERATURERANGE CONTROL REGISTERS N PROGRAMMING PROCEDURE • Use Index byte write. • For N programming, the user only needs to access Byte17, Byte 25, and Byte8. 1. Write Byte17 for CPU PLL N, CPU f = N* Resolution, see resolution table below Byte17. 2. Write Byte25 for SRC PLL N, SRC f = N*0.666667, PCI = SRC f /3, SATA f = SRC f. 3. Enable N Programming bit, Byte8 bit1. Once this bit is enabled, any N value will be changed on the fly. • Center spread only works when the N Programming bit is enabled. Down spread is OK even N Programming bit is disabled • It is OK to change N value to any value on the bench test board. In the system, IDT recommends the stepping change. It is unknown how much the system can sustain for each stepping change; the estimate is about 5. If the N changes too much in one step, the system will likely hang. • Note that SATA is with SRC PLL. This SATA Hard Drive might not operate during SRC N programming. Most of the Bytes, from Byte8-Byte31, are used to adjust output waveforms and SSC modulation profiles. The power on setting will be changed according to each power on frequency selection. To avoid mistakes, don’t write on those byte (be careful about Block Write). It is suggested to use the Index Byte write to access bytes. SSC MAGNITUDE CONTROL, SMC et4U.com SMC[2:0] FREQUENCY SELECTION TABLE FS_C, B, A CPU 000 -0.25 101 001 -0.5 DataSheet4U.com 001 100 133 010 -0.75 011 166 011 -1 010 200 100 ±0.125 000 266 101 ±0.25 100 333 110 ±0.375 110 400 111 ±0.5 111 RESERVE DataShee RESOLUTION CPU (MHz) 100 133 166 200 266 333 400 Resolution 0.666667 0.666667 1.333333 1.333333 1.333333 2.666667 2.666667 N= 150 200 125 150 200 125 150 DataSheet4U.com 5 5 Page www.DataSheet4U.com IDTCV110J PROGRAMMABLE FLEXPC CLOCK FOR P4 PROCESSOR COMMERCIALTEMPERATURERANGE ELECTRICAL CHARACTERISTICS - CPU, SRC, AND DOT96 0.7 CURRENT MODE DIFFERENTIAL PAIR(1) Following Conditions Apply Unless Otherwise Specified: Operating Condition: TA = 0°C to +70°C, Supply Voltage: VDD = 3.3V ± 5%; CL = 2pF Symbol ZO VOH3 VOL3 VHIGH VLOW VOVS VUDS VCROSS(ABS) d - VCROSS ppm TPERIOD Parameter Test Conditions Current Source Output Impedance(2) VO = VX Output HIGH Voltage IOH = -1mA Output LOW Voltage IOL = 1mA Voltage HIGH(2) Voltage LOW(2) Max Voltage(2) Statistical measurement on single-ended signal using oscilloscope math function Measurement on single-ended signal using absolute value Min Voltage(2) Crossing Voltage (abs)(2) Crossing Voltage (var)(2) Variation of crossing over all edges Long Accuracy(2,3) See TPERIOD Min. - Max. values 400MHz nominal/spread 333.33MHz nominal/spread 266.66MHz nominal/spread Average Period(3) 200MHz nominal/spread Min. 3000 2.4 — 660 –150 — –300 250 — –300 2.4993 2.9991 3.7489 4.9985 Typ. — — — — — — — — — — — — — — Max. — — 0.4 850 150 1150 — 550 140 300 2.5008 3.0009 3.7511 5.0015 Unit Ω V V mV mV mV mV ppm ns et4U.com 166.66MHz nominal/spread 133.33MHz nominal/spread 100MHz nominaDl/saprteaaSdheet4U.com 5.9982 7.4978 9.997 — — — 6.0018 7.5023 10.003 DataShee TABSMIN Absolute Min Period(2,3) 96MHz nominal 400MHz nominal/spread 333.33MHz nominal/spread 266.66MHz nominal/spread 200MHz nominal/spread 166.66MHz nominal/spread 133.33MHz nominal/spread 100MHz nominal/spread 10.4135 2.4143 2.9141 3.6639 4.9135 5.9132 7.4128 9.912 — — — — — — — — 10.4198 — — — — — — — ns tR tF d-tR d-tF dT3 tSK3 tJCYC-CYC Rise Time(2) Fall Time(2) Rise Time Variation(2) Fall Time Variation(2) Duty Cycle(2) Skew(2) Jitter, Cycle to Cycle(2) 96MHz nominal VOL = 0.175V, VOH = 0.525V VOL = 0.175V, VOH = 0.525V Measurement from differential waveform VT = 50% Measurement from differential waveform 10.1635 — — 175 — 700 ps 175 — 700 ps — — 125 ps — — 125 ps 45 — 55 % — — 100 ps — — 85 ps NOTES: 1. SRC clock outputs run only at 100MHz or 200MHz. Specs for 133.33 and 166.66 do not apply to SRC clock pair. 2. This parameter is guaranteed by design, but not 100% production tested. 3. All long term accuracy and clock period specifications are guaranteed with the assumption that the REF output is at 14.31818MHz. DataSheet4U.com 11 11 Page

Páginas	Total 16 Páginas
PDF Descargar	[ Datasheet IDTCV110J.PDF ]

Hoja de datos destacado

Número de pieza	Descripción	Fabricantes
IDTCV110J	PROGRAMMABLE FLEXPC CLOCK FOR P4 PROCESSOR	Integrated Device Technology
IDTCV110L	PROGRAMMABLE FLEXPC CLOCK	IDT

Número de pieza	Descripción	Fabricantes
SLA6805M	High Voltage 3 phase Motor Driver IC.	Sanken
SDC1742	12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.	Analog Devices

DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.

DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar