|
|
PDF LB8649FN Data sheet ( Hoja de datos )
| Número de pieza | LB8649FN | |
| Descripción | Motor Driver | |
| Fabricantes | Sanyo Electric | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LB8649FN (archivo pdf) en la parte inferior de esta página. Total 9 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
Ordering number : ENN*7893
LB8649FN Monolithic Digital IC
Motor Driver for DSCs
Feature
• Actuator drivers for digital cameras embedded in one chip.
1. Constant current output car stepping motor for SH/AE or VCM × 2
2. Constant voltage output car stepping motor for ZOOM or DC motor driver
(Normal rotation/Reverse rotation/Brake)
3. Constant voltage output car stepping motor for AF
• No standby current consumption (or zero). (Direct battery connection possible.)
• 4 systems for independent power supply (SH/AE, AF, ZOOM or input logic system)
• Low voltage driving (Driving by two nickel hydride batteries possible)
• Built-in thermal protection circuitry
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Max. Power Source Voltage
VB max
VB power supply
Max. Input Applied Voltage
Max. Output Applied Voltage
Max. Output Current
Allowable Power Consumption
VCC max
VIN max
VOUT max
IO max
Pd max
VCC power supply
per CH
Circuit board mounting (*1)
Operating Temperature
Topr
Storage Temperature
Tstg
(*1) Mounting circuit board : 50.0mm × 50.0mm × 0.8mm glass epoxy resin
Ratings
10.5
10.5
10.5
10.5
600
1.0
-20 to +80
-55 to +150
Unit
V
V
V
mA
W
°C
°C
www.DataSheet4U.com
82504 JO IM No.7893-1/9
1 page  
www.DataSheet4U.com
LB8649FN
3. VCM constant current control for SH/AE, or stepping motor drive.
Input
Output
IN9
IN10
IN11
IN12
INHD
OUT9 OUT10 OUT11 OUT12
Vref
ISH
Mode
LLLL
-----
-
Stand-by
HL * *
HL
LH * * L LH
1.0V
SH & AE
* *HL
HL
Setting
* * LH
LH
voltage
HL * *
HL
state
LH * *
LH
Hold
* *HLH
H L 0.67V
* * LH
LH
LLLL
----
Discharge
Stand-by
• ( - ) is output OFF, and ( * ) is “Don’t care”.
• OUT9 and OUT10 are used for the SH.
Quick charge and quick discharge circuitry allows the stabilization of start-up characteristic.
• OUT10 and OUT11 are used for the AF.
• At the time of stand-by, ISH pin voltage becomes discharge state by the internal transistor and it is set to 0V.
• In addition, when IN1 to 8 are input, ISH pin is in discharge state (for start-up correction).
• When INHD = “L”, Vref voltage is 1.0V. When INHD = “H”, Vref voltage is 0.67V.
Application Design Notes
1. Constant current setting (ISH, IAE, RFG1, 2, OUT9 to 12)
The constant current setting between pins OUT9 and OUT10 is determined from the ISH input voltage and the
connecting resistor of RFG1. As shown in the block diagram, it is controlled in such a way so that the voltage
generated at the resistor used for current detection connected between RFG1 and GND would be equal to the ISH
input voltage. The formula for calculating the output current is as given below.
(OUT9 to OUT10 Output Current) = (ISH Input Voltage) ÷ (RFG1 Resistor + 0.05Ω)
The 0.05Ω here is for a common impedance of the output Tr emitter which drives constant current in the RFG pin
and the sensing wiring for the constant current control amplifier.
In the same way, the constant current setting between pins OUT11 and OUT12 is determined from the IAE input
voltage and the connecting resistor of RFG2.
Furthermore, as the constant current control block within the IC is connected to PGND, when supplying voltage to
the ISH pin or IAE pin which has been divided by resistors be sure to connect the ground side of these resistors to
PGND.
2. Quick charge/discharge circuitry (FC1, OUT9, OUT10)
Quick discharge circuitry has been built in to the shutter control block (OUT9 to OUT10) to support high-speed
shutter control, quick recharge, quick discharge and consecutive shots.
Quick recharge and quick discharge circuitry has not been built in to the AE control block (OUT11 to OUT12).
Therefore, make sure to use the block (OUT9 to OUT10) for the shutter drive.
www.DataSheet4U.com
No.7893-5/9
5 Page | ||
| Páginas | Total 9 Páginas | |
| PDF Descargar | [ Datasheet LB8649FN.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LB8649FN | Motor Driver | Sanyo Electric |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |