IN74HC4053A Datasheet PDF - IK Semiconductor
| Part Number | IN74HC4053A | |
| Description | Tripple 2-Channel Analog Multiplexer/Demultiplexer | |
| Manufacturers | IK Semiconductor | |
| Logo |  |
|
|
There is a preview and IN74HC4053A download ( pdf file ) link at the bottom of this page. Total 9 Pages | ||
Preview 1 page No Preview Available !
TECHNICAL DATA
Analog Multiplexer/Demultiplexer
High-Performance Silicon-Gate CMOS
IN74HC4053A
The IN74HC4053A utilize silicon-gate CMOS technology to achieve
fast propagation delays, low ON resistances, and low OFF leakage
currents. These analog multiplexers/demultiplexers control analog
voltages that may vary across the complete power supply range (from VCC
to VEE).
The Channel-Select inputs determine which one of the Analog
Inputs/Outputs is to be connected, by means of an analog switch, to the
Common Output/Input.When the Enable pin is high, all analog switches
are turned off.
The Channel-Select and Enable inputs are compatible with standard
CMOS outputs; with pullup resistors, they are compatible with
LS/ALSTTL outputs.
• Fast Switching and Propagation Speeds
• Low Crosstalk Between Switches
• Diode Protection on All Inputs/Outputs
• Analog Power Supply Range (VCC-VEE)=2.0 to 12.0 V
• Digital (Control) Power Supply Range (VCC-GND)=2.0 to 6.0 V
• Low Noise
ORDERING INFORMATION
IN74HC4053AN Plastic
IN74HC4053ADW SOIC
TA = -55° to 125° C for all packages
PIN ASSIGNMENT
LOGIC DIAGRAM
Triple Single-Pole, Double-Position
Plus Common Off
omPIN 16 =VCC
.cPIN 7 = VEE
www.datasheet4u PIN 8 = GND
FUNCTION TABLE
Control Inputs
Enable Select
CBA
L LLL
L LLH
L LHL
L LHH
L HLL
L HLH
L HHL
L HHH
H XXX
X = don’t care
ON
Channels
Z0 Y0 X0
Z0 Y0 X1
Z0 Y1 X0
Z0 Y1 X1
Z1 Y0 X0
Z1 Y0 X1
Z1 Y1 X0
Z1 Y1 X1
None
1
|
| |
 
IN74HC4053A
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0.0 V)
Symbol
BW
-
Parameter
Maximum On-
Channel
Bandwidth or
Minimum
Frequency
Response
(Figure 5)
Off-Channel
Feedthrough
Isolation
(Figure 6)
Test Conditions
fin=1 MHz Sine Wave
Adjust fin Voltage to Obtain 0 dBm at VOS
Increase fin Frequence Until dB Meter
Reads -3 dB
RL =50 Ω, CL=10 pF
fin= Sine Wave
Adjust fin Voltage to Obtain 0 dBm at VIS
fin = 10 kHz, RL =600 Ω, CL=50 pF
fin = 1.0 MHz, RL =50 Ω, CL=10 pF
- Feedthrough VIN≤ 1 MHz Square Wave (tr = tf = 6 ns)
Noise, Channel Adjust RL at Setup so that IS= 0 A Enable
Select Input to = GND
Common O/I
(Figure 7)
RL =600 Ω, CL=50 pF
RL =10 Ω, CL=10 pF
- Crosstalk
fin= Sine Wave
Between Any Adjust fin Voltage to Obtain 0 dBm at VIS
Two Switches
fin = 10 kHz, RL =600 Ω, CL=50 pF
(Figure 14)
fin = 1 MHz, RL =50 Ω, CL=10 pF
THD
Total Harmonic
Distortion
(Figure 16)
fin= 1 kHz, RL =10 kΩ, CL=50 pF
THD = THDMeasured - THDSource
VIS =4.0 VPP sine wave
VIS =8.0 VPP sine wave
VIS =11.0 VPP sine wave
* Limits not tested. Determined by design and verified by qualification.
VCC
V
2.25
4.50
6.00
2.25
4.50
6.00
2.25
4.50
6.00
2.25
4.50
6.00
2.25
4.50
6.00
2.25
4.50
6.00
2.25
4.50
6.00
2.25
4.50
6.00
VEE
V
-2.25
-4.50
-6.00
-2.25
-4.50
-6.00
-2.25
-4.50
-6.00
-2.25
-4.50
-6.00
-2.25
-4.50
-6.00
-2.25
-4.50
-6.00
-2.25
-4.50
-6.00
-2.25
-4.50
-6.00
Limit*
25 °C
Unit
MHz
120
120
120
dB
-50
-50
-50
-40
-40
-40
mVpp
25
105
135
35
145
190
dB
-50
-50
-50
-60
-60
-60
%
0.10
0.08
0.05
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for IN74HC4053A electronic component. |
| Information | Total 9 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ IN74HC4053A.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| IN74HC4053A | The function is Tripple 2-Channel Analog Multiplexer/Demultiplexer. IK Semiconductor | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
IN74
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||