DataSheetWiki


29LV160BE fiches techniques PDF

Fujitsu Media Devices - MBM29LV160BE

Numéro de référence 29LV160BE
Description MBM29LV160BE
Fabricant Fujitsu Media Devices 
Logo Fujitsu Media Devices 





1 Page

No Preview Available !





29LV160BE fiche technique
FUJITSU SEMICONDUCTOR
DATA SHEET
DS05-20883-2E
FLASH MEMORY
CMOS
16M (2M × 8/1M × 16) BIT
MBM29LV160TE/BE -www.DataSheet4U.com
70/90/12
s GENERAL DESCRIPTION
The MBM29LV160TE/BE is a 16M-bit, 3.0 V-only Flash memory organized as 2M bytes of 8 bits each or 1M words
of 16 bits each. The MBM29LV160TE/BE is offered in a 48-pin TSOP (I), 48-pin CSOP and 48-ball FBGA
packages. The device is designed to be programmed in-system with the standard system 3.0 V VCC supply. 12.0
V VPP and 5.0 V VCC are not required for write or erase operations. The device can also be reprogrammed in
standard EPROM programmers.
The standard MBM29LV160TE/BE offers access times of 70 ns, 90 ns and 120 ns, allowing operation of high-
speed microprocessors without wait states. To eliminate bus contention the device has separate chip enable (CE),
write enable (WE), and output enable (OE) controls.
The MBM29LV160TE/BE is pin and command set compatible with JEDEC standard E2PROMs. Commands are
written to the command register using standard microprocessor write timings. Register contents serve as input
to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch
addresses and data needed for the programming and erase operations. Reading data out of the device is similar
to reading from 5.0 V and 12.0 V Flash or EPROM devices.
The MBM29LV160TE/BE is programmed by executing the program command sequence. This will invoke the
Embedded ProgramTM* Algorithm which is an internal algorithm that automatically times the program pulse widths
and verifies proper cell margins. Typically, each sector can be programmed and verified in about 0.5 seconds.
Erase is accomplished by executing the erase command sequence. This will invoke the Embedded EraseTM*
Algorithm which is an internal algorithm that automatically preprograms the array if it is not already programmed
before executing the erase operation. During erase, the device automatically times the erase pulse widths and
verifies proper cell margins.
Any individual sector is typically erased and verified in 1.0 second. (If already preprogrammed.)
within a sector simultaneously via Fowler-Nordhiem tunneling. The bytes/words are programmed one byte/word
at a time using the EPROM programming mechanism of hot electron injection.
s PRODUCT LINE UP
(Continued)
Part No.
Ordering Part No.
VCC
=
3.3
V
+0.3 V
–0.3 V
VCC
=
3.0
V
+0.6 V
–0.3 V
Max. Address Access Time (ns)
Max. CE Access Time (ns)
Max. OE Access Time (ns)
MBM29LV160TE/160BE
70 —
— 90 12
70 90 120
70 90 120
30 35 50

PagesPages 30
Télécharger [ 29LV160BE ]


Fiche technique recommandé

No Description détaillée Fabricant
29LV160B 16 Megabit CMOS 3 Volt-only Sector Erase Flash Memory AMD
AMD
29LV160BE MBM29LV160BE Fujitsu Media Devices
Fujitsu Media Devices
29LV160BE MBM29LV160BE Fujitsu Media Devices
Fujitsu Media Devices
29LV160BT MX29LV160BT Macronix International
Macronix International

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche