|
|
Número de pieza | ICX239AKE | |
Descripción | CCD Image Sensor with Square Pixel for Color Cameras | |
Fabricantes | Sony | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ICX239AKE (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
No Preview Available ! ICX239AKE
Diagonal 3mm (Type 1/6) CCD Image Sensor for PAL Color Cameras
Description
The ICX239AKE is an interline CCD solid-state
image sensor suitable for PAL small color cameras.
High resolution is achieved through the use of Ye,
Cy, Mg, and G complementary color mosaic filters.
This chip features a field period readout system and
an electronic shutter with variable charge-storage time.
The package is a small 12-pin SON(LCC).
12 pin SON (Ceramic)
Features
• High sensitivity and low smear
• Horizontal register: 3.3 to 5.0V drive
• Reset gate:
3.3 to 5.0V drive
• No voltage adjustment
(Reset gate and substrate bias are not adjusted.)
• Low dark current and excellent antiblooming characteristics
• Continuous variable-speed shutter
• Recommended range of exit pupil distance: –10mm to – ∞
• Ye, Cy, Mg, and G complementary color mosaic filters on chip
• 12-pin ceramic SON(LCC) package
V
3
Pin 7
Pin 1
2
12
H 40
Device Structure
• Interline CCD image sensor
• Image size:
• Number of effective pixels:
• Total number of pixels:
• Chip size:
• Unit cell size:
• Optical black:
• Number of dummy bits:
• Substrate material:
Optical black position
(Top View)
Diagonal 3mm (Type 1/6)
752 (H) × 582 (V) approx. 440K pixels
795 (H) × 596 (V) approx. 470K pixels
3.30mm (H) × 2.95mm (V)
3.275µm (H) × 3.150µm (V)
Horizontal (H) direction: Front 3 pixels, rear 40 pixels
Vertical (V) direction: Front 12 pixels, rear 2 pixels
Horizontal 22
Vertical 1 (even fields only)
Silicon
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E98X20A99-PS
1 page ICX239AKE
Drive Clock Waveform Conditions
(1) Readout clock waveform
100%
90%
II II
10%
0%
tr
(2) Vertical transfer clock waveform
Vφ1
VVT
twh
tf
Vφ3
φM
φM
2
0V
VVH1
VVHH
VVH
VVHH
VVHL
VVHL
VVHL
VVHH
VVHH
VVH3
VVHL
VVH
VVL1
VVLH
VVLL
VVL
Vφ2
VVHH
VVH2 VVHL
VVHH
VVH
VVHL
VVL3
VVL
Vφ4
VVH
VVHH
VVLH
VVLL
VVHH
VVHL
VVHL
VVH4
VVL2VVLH
VVLL
VVL
VVH = (VVH1 + VVH2)/2
VVL = (VVL3 + VVL4)/2
VφV = VVHn – VVLn (n = 1 to 4)
VVLH
VVLL
VVL4
–5–
VVL
5 Page ICX239AKE
6. Uniformity between video signal channels
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then measure the maximum (Crmax, Cbmax [mV]) and minimum (Crmin, Cbmin
[mV]) values of the R – Y and B – Y channels of the chroma signal and substitute the values into the
following formula.
∆Sr = | (Crmax – Crmin)/200 | × 100 [%]
∆Sb = | (Cbmax – Cbmin)/200 | × 100 [%]
7. Dark signal
Measure the average value of the Y signal output (Ydt [mV]) with the device ambient temperature 60°C and
the device in the light-obstructed state, using the horizontal idle transfer level as a reference.
8. Flicker
1) Fy
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then measure the difference in the signal level between fields (∆Yf [mV]). Then
substitute the value into the following formula.
Fy = (∆Yf/200) × 100 [%]
2) Fcr, Fcb
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, insert an R or B filter, and then measure both the difference in the signal level between
fields of the chroma signal (∆Cr, ∆Cb) as well as the average value of the chroma signal output (CAr, CAb).
Substitute the values into the following formula.
Fci = (∆Ci/CAi) × 100 [%] (i = r, b)
9. Line crawls
Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then insert a white subject and R, G, and B filters and measure the difference
between Y signal lines for the same field (∆Ylw, ∆Ylr, ∆Ylg, ∆Ylb [mV]). Substitute the values into the
following formula.
Lci = (∆Yli/200) × 100 [%] (i = w, r, g, b)
– 11 –
11 Page |
Páginas | Total 17 Páginas | |
PDF Descargar | [ Datasheet ICX239AKE.PDF ] |
Número de pieza | Descripción | Fabricantes |
ICX239AKC | Diagonal 3mm (Type 1/6) CCD Image Sensor | Sony |
ICX239AKE | CCD Image Sensor with Square Pixel for Color Cameras | Sony |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |