SA1630 Datasheet PDF - Philips
| Part Number | SA1630 | |
| Description | IF quadrature transceiver | |
| Manufacturers | Philips | |
| Logo |  |
|
|
There is a preview and SA1630 download ( pdf file ) link at the bottom of this page. Total 22 Pages | ||
Preview 1 page No Preview Available !
INTEGRATED CIRCUITS
SA1630
IF quadrature transceiver
Product specification
IC17 Data Handbook
Philips
Semiconductors
1998 Jul 21
|
| |
 
Philips Semiconductors
IF quadrature transceiver
Product specification
SA1630
ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
VCCXX
VIN
∆VG
PD
TJMAX
PMAX
TSTG
Supply voltages
Voltage applied to any other pin
Any GND pin to any other GND pin
Power dissipation, TA = 25°C (still air)
Maximum operating junction temperature
Maximum power input/output
Storage temperature range
RATING
-0.3 to +6.0
-0.3 to VCCXX+0.3
0
300
150
+20
–65 to +150
UNITS
V
V
V
mW
°C
dBm
°C
RECOMMENDED OPERATING CONDITIONS
SYMBOL
PARAMETER
VCCXXXX
VCCCP
TA
Supply voltages:
Charge pump supply voltage
Operating ambient temperature range
RATING
2.7 to 3.6
2.7 to 3.6
-40 to +85
UNITS
V
V
°C
NOTES:
1. There are no ESD protection diodes between pins 42, 43 and VCC to allow higher AC peak voltage. The ESD protection level has thus been
reduced. Proper ESD handling precautions should be followed.
MODE CONTROL
NO: PLL_ON
10
21
31
41
51
’0’ – LOGIC LOW
’1’ – LOGIC HIGH
’X’ – DON’T CARE
RX_ON
X
0
1
1
0
TX_ON
X
1
1
0
0
STATE DESCRIPTION
SLEEP mode
Synthesizer ON, Rx STDBY, Tx OFF
Synthesizer ON, Rx STDBY, Tx ON
Synthesizer ON, Rx ON, Tx OFF
Synthesizer ON, Rx OFF, Tx ON
MODE
SLEEP
WAIT
TRANSMIT
RECEIVE
TRANSMIT
2.5V REF
Off
Off
On
Off
Off
1. Sleep mode (PLL OFF, Rx OFF, Tx OFF)
In this mode everything is switched off except the 3–wire digital bus.
As long as the digital supply is still on, the programmed values are
active and the 3–wire bus will continue to be programmable.
2. Wait Mode (Tx Off, Rx Standby)
PLL is on. Receiver is in the reduced current standby mode and the
transmitter is completely switched off. This mode maybe useful if the
PLL is to be kept on and is waiting for a quick turn–on to either
transmit or receive modes, especially when Rx outputs are AC
coupled.
3. Transmit mode (Rx standby)
The PLL and transmitter are on. The receive section is in a reduced
current mode wherein most of the Rx circuitry is powered down
except for the bias and baseband circuits needed to hold the
baseband output voltages in the active state. This mode is useful if
the Rx baseband outputs are AC coupled via a large capacitor and
the application demands quick turn–on for the Rx, from Tx.
4. Receive Mode (Tx Off)
The Transmitter is completely shut–off. The PLL and receiver
sections are operating.
5. Transmit Mode (Rx OFF)
PLL and Transmit sections are on. However, the Receiver is
completely shut–down. This mode is useful if the Rx baseband
outputs are DC coupled to the external world.
1998 Jul 21
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for SA1630 electronic component. |
| Information | Total 22 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ SA1630.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| SA1630 | The function is IF quadrature transceiver. Philips | |
| SA1630BE | The function is IF quadrature transceiver. Philips | |
| SA1638 | The function is Low voltage IF I/Q transceiver. Philips | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
SA16
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||