DataSheetWiki


N74F8963Y fiches techniques PDF

Philips - 9-Bit latched bidirectional Futurebus transceivers open-collector

Numéro de référence N74F8963Y
Description 9-Bit latched bidirectional Futurebus transceivers open-collector
Fabricant Philips 
Logo Philips 





1 Page

No Preview Available !





N74F8963Y fiche technique
Philips Semiconductors FAST Products
9-Bit latched bidirectional Futurebus transceivers
(open-collector)
Product specification
74F8962/8963
FEATURES
Octal latched transceiver
Drives heavily loaded backplanes with
equivalent load impedances down to 10
High drive (100mA) open collector drivers
on B port
Reduced voltage swing (1 volt) produces
less noise and reduces power consumption
High speed operation enhances
performance of backplane buses and
facilitates incident wave switching
Compatible with IEEE 896 futurebus
standards
Built–in precision band–gap reference
provides accurate receiver thresholds and
improved noise immunity
Multiple GND pins minimize ground bounce
Glitch–free power up/power down
operation
DESCRIPTION
The 74F8962 and 74F8963 are octal
bidirectional latched transceivers and are
intended to provide the electrical interface to
a high performance wired-OR bus. The B port
inverting drivers are low-capacitance open
collector with controlled ramp and are
designed to sink 100mA from 2 volts. The B
port inverting receivers have a 150mV
threshold region.
The B port interfaces to ‘Backplane
Transceiver Logic’ (BTL). BTL features a
reduced (1V to 2V) voltage swing for lower
power consumption and a series diode on
the drivers to reduce capacitive loading.
Incident wave switching to 9is guaranteed.
The voltage swing is much less for BTL, so is
its receiver threshold region, therefore noise
margins are excellent.
BTL offers low power consumption, low
ground bounce, EMI and crosstalk, low
capacitive loading, superior noise margin and
low propagation delays. This results in a high
bandwidth, reliable backplane.
The 74F8962 and 74F8963 A ports have TTL
3-state drivers and TTL receivers with a latch
function.
The 74F8963 is the non-inverting version of
74F8962.
TYPE
74F8962
74F8963
TYPICAL PROPAGATION DELAY
6.5ns
5.5ns
TYPICAL SUPPLY CURRENT( TOTAL)
90mA
90mA
ORDERING INFORMATION
DESCRIPTION
44–pin Quad Flat Pack1
44–pin Plastic Leaded Chip Carrier
Note to ordering information
1. Flatpack package is not available at this time.
ORDER CODE
COMMERCIAL RANGE
VCC = 5V ±10%, Tamb = 0°C to +70°C
N74F8962Y, N74F8963Y
N74F8962A, N74F8963A
INPUT AND OUTPUT LOADING AND FAN OUT TABLE
PINS
DESCRIPTION
74F (U.L.)
HIGH/LOW
AI0 – AI8
PNP latched inputs
1.0/0.167
B0 – B8
Data inputs with threshold circuitry
5.0/0.167
OEAB, OEBA
Output enable inputs (active low)
1.0/0.033
LEAB, LEBA
Latch enable inputs (active low)
1.0/0.033
AO0 – AO8
3–state outputs
150/40
B0 – B8
Open collector outputs
Notes to input and output loading and fan out table
1. One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state.
2. OC = Open collector.
OC/166.7
LOAD VALUE
HIGH/LOW
20µA/100µA
100µA/100µA
20µA/20µA
20µA/20µA
3mA/24mA
OC/100mA
March 11, 1993
1 853–1425 09230

PagesPages 10
Télécharger [ N74F8963Y ]


Fiche technique recommandé

No Description détaillée Fabricant
N74F8963A 9-Bit latched bidirectional Futurebus transceivers open-collector Philips
Philips
N74F8963Y 9-Bit latched bidirectional Futurebus transceivers open-collector Philips
Philips

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche