M29W641DU90N6T Datasheet PDF - ST Microelectronics
| Part Number | M29W641DU90N6T | |
| Description | 64 Mbit 4Mb x16 / Uniform Block 3V Supply Flash Memory | |
| Manufacturers | ST Microelectronics | |
| Logo |  |
|
|
There is a preview and M29W641DU90N6T download ( pdf file ) link at the bottom of this page. Total 42 Pages | ||
Preview 1 page No Preview Available !
M29W641DH, M29W641DL
M29W641DU
64 Mbit (4Mb x16, Uniform Block)
3V Supply Flash Memory
PRODUCT PREVIEW
FEATURES SUMMARY
s SUPPLY VOLTAGE
– VCC = 2.7V to 3.6V Core Power Supply
– VCCQ = 1.8V to 3.6V for Input/Output
– VPP =12 V for Fast Program (optional)
s ACCESS TIME: 70, 90, 100 and 120ns
s PROGRAMMING TIME
– 10 µs typical
– Double Word Program option
s 128 UNIFORM, 32-KWord MEMORY BLOCKS
s PROGRAM/ERASE CONTROLLER
– Embedded Program and Erase algorithms
s ERASE SUSPEND and RESUME MODES
– Read and Program another Block during
Erase Suspend
s UNLOCK BYPASS PROGRAM COMMAND
– Faster Production/Batch Programming
s WRITE PROTECT OPTIONS
– M29W641DH: WP Pin for Write Protection of
Highest Address Block
– M29W641DL: WP Pin for Write Protection of
Lowest Address Block
– M29W641DU: No Write Protection
s TEMPORARY BLOCK UNPROTECTION
MODE
s COMMON FLASH INTERFACE
s EXTENDED MEMORY BLOCK
– Extra block used as security block or to store
additional information
s LOW POWER CONSUMPTION
– Standby and Automatic Standby
s ELECTRONIC SIGNATURE
– Manufacturer Code: 0020h
– Device Code M29W641D: 22C7h
Figure 1. Packages
TSOP48 (N)
12 x 20mm
FBGA
TFBGA63 (ZA)
7 x 11mm
April 2003
This is preliminary information on a new product now in development. Details are subject to change without notice.
1/42
|
| |
 
M29W641DH, M29W641DL, M29W641DU
SUMMARY DESCRIPTION
The M29W641D is a 64 Mbit (4Mb x16) non-vola-
tile memory that can be read, erased and repro-
grammed. These operations can be performed
using a single, low voltage, 2.7V to 3.6V VCC sup-
ply for the circuitry and a 1.8V to 3.6V VCCQ supply
for the Input/Output pins. An optional 12 V VPP
power supply is provided to speed up customer
programming.
On power-up the memory defaults to its Read
mode where it can be read in the same way as a
ROM or EPROM.
The highest address block of the M29W641DH or
the lowest address block of the M29W641DL can
be protected from accidental programming or era-
sure using the WP pin (if WP = VIL). The
M29W641DU does not feature the WP pin.
Each block can be erased independently so it is
possible to preserve valid data while old data is
erased. The blocks can be protected to prevent
accidental Program or Erase commands from
modifying the memory. Program and Erase com-
mands are written to the Command Interface of
the memory. An on-chip Program/Erase Controller
simplifies the process of programming or erasing
the memory by taking care of all of the special op-
erations that are required to update the memory
contents. The end of a program or erase operation
can be detected and any error conditions identi-
fied. The command set required to control the
memory is consistent with JEDEC standards.
The M29W641D has an extra block, the Extended
Block, (of 32 KWords) that can be accessed using
a dedicated command. The Extended Block can
be protected and so is useful for storing security
information. However the protection is not revers-
ible, once protected the protection cannot be un-
done.
Chip Enable, Output Enable and Write Enable sig-
nals control the bus operation of the memory.
They allow simple connection to most micropro-
cessors, often without additional logic.
The memory is offered in a 48-pin TSOP package
(M29W641DL and M29W641DH) or in a 63-ball TF-
BGA package (M29W641DU). All devices are deliv-
ered with all the bits erased (set to 1).
Figure 2. Logic Diagram
VCC VCCQ VPP
22
A0-A21
16
DQ0-DQ15
W
E M29W641D
G
RB
RP
WP
VSS
AI06697b
Table 1. Signal Names
A0-A21
Address Inputs
DQ0-DQ7 Data Inputs/Outputs
DQ8-
DQ15
Data Inputs/Outputs
E Chip Enable
G Output Enable
W Write Enable
RP
Reset/Block Temporary Unprotect
(M29W641DH and M29W641DL only)
RB
Ready/Busy Output (M29W641DU
only)
WP Write Protect
VCC
VCCQ
Supply Voltage
Supply Voltage for Input/Output
VPP
Supply Voltage for Fast Program
(optional)
VSS Ground
5/42
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for M29W641DU90N6T electronic component. |
| Information | Total 42 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ M29W641DU90N6T.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| M29W641DU90N6E | The function is 64 Mbit 4Mb x16 / Uniform Block 3V Supply Flash Memory. ST Microelectronics | |
| M29W641DU90N6F | The function is 64 Mbit 4Mb x16 / Uniform Block 3V Supply Flash Memory. ST Microelectronics | |
| M29W641DU90N6T | The function is 64 Mbit 4Mb x16 / Uniform Block 3V Supply Flash Memory. ST Microelectronics | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
M29W
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||