M66335FP Datasheet PDF - Mitsubishi
| Part Number | M66335FP | |
| Description | FACSIMILE IMAGE DATA PROCESSOR | |
| Manufacturers | Mitsubishi | |
| Logo |  |
|
|
There is a preview and M66335FP download ( pdf file ) link at the bottom of this page. Total 30 Pages | ||
Preview 1 page No Preview Available !
MITMSIUTSBUISBHISI 〈HDII〈GDIITGAILTAALSASSPS〉 P〉
M663M36563F35PFP
FACFSAICMSILIMEILIMEAIMGEAGDEATDAAPTAROPRCOESCSEOSSROR
DESCRIPTION
The M66335 is a facsimile image processing controller to turn into
binary signals analog signals which have been output through photo-
electric conversion by the image sensor.
The image processing functions includes peak value detection,
uniformity correction, resolution change, MTF compensation, γ cor-
rection, detection of background/character levels, error diffusion,
separation of image zones, and designation of regions.
This controller contains not only the analog processing circuit, the A/
D converter of a 7-bit flash type and image processing memory, but
also the image sensor and the interface circuit to the CODEC (Coder
and Decoder). Therefore, this LSI alone is capable of image pro-
cessing.
FEATURES
• High speed scan (max. 2 ms/line, typ. 5 ms/line)
• Compatibility with up to the B4 (8 pixels/mm, 16 pixels/mm) image
sensor
• Generation of control signals for the image sensor (CCD, CIS)
For CCD: SH, CK1, CK2, RS
For the contact sensor (CIS): SH, CK1, CK2
• Built-in analog processing circuit (equivalent to the M64291)
Sample and hold circuit
Gain control circuit
Black level clamping circuit
Reference internal power supply for the A/D converter
PIN CONFIGURATION (TOP VIEW)
• Built-in A/D converter of a 7-bit flash type
• Built-in image processing memories
Uniformity correction memory, Line memory, Error memory, γ cor-
rection memory
• External output interface for converted binary data
Serial output (→ M66330)
DMA output
• External output interface for multivalued data
DMA transfer of data compensated for uniformity
• Various image processing functions
Uniformity correction
Resolution change from 50% to 200% (by the 1% step)
MTF compensation (2-dimensional processing, capable of correc-
tion for each character/photo)
γ correction (capable of correction for each character/photo)
Detection of background/character levels
Change to pseudo-halftone
• Error diffusion (64 tone steps through 6-bit processing)
• Organized dither (64 tone steps through the 8 × 8 matrix)
Image zone separation (2-dimensional processing)
• 5V single power supply
APPLICATION
Facsimile, word processor and image scanner
MPU
INTERFACE
DMA
INTERFACE
SYSTEM CLOCK
NC 65
A0 → 66
A1 → 67
A2 → 68
A3 → 69
A4 → 70
CS → 71
RD → 72
WR → 73
RESET → 74
DAK → 75
DRQ ← 76
INT ← 77
SYSCK → 78
GND 79
NC 80
M66335FP
40 NC
39 DGND
38 DVCC
37 VBL ADC BLACK REFERENCE OUTPUT
36 VWL ADC WHITE REFERENCE OUTPUT
35 ← ADIN ADC INPUT
34 AVCC
33 Vri+ ADC WHITE REFERENCE INPUT
32 AGND
31 Vri- ADC BLACK REFERENCE INPUT
30 → BCMO
29 ← BCMV CONTROL SIGNAL FOR
28 ← BCMI ANALOG SIGNAL
27 ← C2 PROCESSING
26 ← C1
25 NC
Outline 80P6N–A
NC: No Connection
1
|
| |
 
MITSUBISHI 〈DIGITAL ASSP〉
M66335FP
FACSIMILE IMAGE DATA PROCESSOR
(1) Operation mode
The M66335 has three basic operations.
• Peak value detection: Adjusting the peak value of analog signals
output from the analog circuit to the white reference voltage (VWL)
of the A/D converter built in the M66335.
• Generation of data for uniformity correction: Generating data on
a white reference original sheet for uniformity correction by the
sensor unit and writing them to the memory for correction built
in the M66335.
• Read: Reading original sheets, performing image processing of
the read image data, and outputting in serial or parallel the indi-
cated converted binary data.
The M66335 is capable of performing the DMA transfer of
multivalued data (6-bit data=D7~D2, D1=D0=0) after correction
about uniformities.
These three basic operations are performed in the following mode
sequences for the CCD sensor and CIS sensor. The sensor is set
through the register 00 (SENS).
For the CCD sensor
AGC mode
The peak value of the 16 line cycle is de-
tected by setting the AGC command in
the register 00 at “H”.
To escape this mode, set the AGC com-
mand at “L” after a 20 line cycle (or a cycle
of 16 lines or more) passed since the
start.
UNIF mode (white)
This operation mode is started by setting
the UNIF command in the register 00 at
“H” after setting UMODE: “H” (white cor-
rection) in the register 00 and UNIFM: “L”
(only white correction) in the register 01.
Starting by the UNIF command also
makes the system generate data for non-
uniformity correction for white correction
(for the 8 line cycle).
To escape this mode, set the UNIF com-
mand at “L” after a 10 line cycle (or a cycle
of 8 lines or more) passed since the start.
SCAN mode
The read operation mode is started by
setting the SCAN command in the regis-
ter 00 at “H”. To escape this mode, set
the SCAN command at “L”.
For the CIS sensor
AGC mode
The peak value of the 16 line cycle is
detected by setting the AGC command
in the register 00 at “H”.
To escape this mode, set the AGC com-
mand at “L” after a 20 line cycle (or a cycle
of 16 lines or more) passed since the
start.
UNIF mode (black)
When this operation mode is started by
the UNIF command after setting UMODE:
“L” (black correction) in the register 00
and UNIFM: “H” (black and white correc-
tion) in the register 01, the system also
generates black data for non-uniformity
correction for black correction (for the 8
line cycle).
To escape this mode, set the UNIF com-
mand at “L” after a 10 line cycle (or a cycle
of 8 lines or more) passed since the start.
In the case of only white correction, the
setting is not necessary. Follow the
instruction below.
UNIF mode (white)
When this operation mode is started by
the UNIF command in the register 00 af-
ter setting UMODE: “H” (white correction)
in the register 00 and UNIFM: “L” (only
white correction) in the register 01, the
system also generates white data for non-
uniformity correction for white correction
(for the 8 line cycle).
To escape this mode, set the UNIF com-
mand at “L” after a 10 line cycle (or a cycle
of 8 lines or more) passed since the start.
SCAN mode
The reading operation is started by set-
ting the SCAN command in the register
00 at “H”. To escape this mode, set the
SCAN mode at “L”.
The signal operations and data flow
in each basic operation are shown in
the page 4-217 and 4-218, and the flow-
chart is in the page 4-260 and 4-261.
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for M66335FP electronic component. |
| Information | Total 30 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ M66335FP.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| M66335FP | The function is FACSIMILE IMAGE DATA PROCESSOR. Mitsubishi | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
M663
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||