|
|
Número de pieza | TDA7072 | |
Descripción | Single BTL power driver | |
Fabricantes | NXP Semiconductors | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de TDA7072 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! INTEGRATED CIRCUITS
DATA SHEET
TDA7072A/AT
Single BTL power driver
Objective specification
File under Integrated circuits, IC01
July 1994
1 page Philips Semiconductors
Single BTL power driver
Objective specification
TDA7072A/AT
CHARACTERISTICS
VP = 5 V; f = 1 kHz; Tamb = 25 °C; unless otherwise specified (see Fig.3>). TDA7072A: RL = 8 Ω;
TDA7072AT: RL = 16 Ω.
SYMBOL
PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
VP
IORM
IP
∆VOUT
THD
Gv
Vno(rms)
B
SVRR
|∆V5-8|
VI(CM)
CMRR
ZI
Ibias
SR
positive supply voltage range
repetitive peak output current
total quiescent current
output voltage swing
total harmonic distortion
TDA7072A
TDA7072AT
voltage gain
noise output voltage (RMS value)
bandwidth
supply voltage ripple rejection
DC output offset voltage
DC common mode voltage range
DC common mode rejection ratio
input impedance
input bias current
slew rate
RL = ∞; note 1
note 2
VOUT = 1 V (RMS)
note 3
note 4
RS = 500 Ω
note 5
note 6
3.0 5.0 18 V
− − 0.6 A
− 4 8 mA
5.2 5.8 −
V
− 0.3 − %
− 0.1 − %
32.5 33.5 34.5 dB
− 75 150 µV
− − 1.5 MHz
40 55 −
dB
− − 100 mV
0 − 2.8 V
− 100 − dB
− 100 − kΩ
− 100 300 nA
− 12 − V/µs
Notes to the characteristics
1. With a load connected to the outputs the quiescent current will increase, the maximum value of this increase being
equal to the DC output offset voltage divided by RL.
2. The output voltage swing is typically limited to 2 x (VP −2.1 V) (see Fig.4).
3. The noise output voltage (RMS value), unweighted (20 Hz to 20 kHz) is measured with RS = 500 Ω.
4. The ripple rejection is measured with RS = 0 Ω and f = 100 Hz to 10 kHz. The ripple voltage of 200 mV (RMS value)
is applied to the positive supply rail.
5. The DC common mode voltage range is limited to (VP −2.2 V).
6. The common mode rejection ratio is measured at Vref = 1.4 V, VI(CM) = 200 mV and f = 1 kHz.
July 1994
5
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet TDA7072.PDF ] |
Número de pieza | Descripción | Fabricantes |
TDA7072 | Single BTL power driver | NXP Semiconductors |
TDA7072A | Single BTL power driver | NXP Semiconductors |
TDA7072AT | Single BTL power driver | NXP Semiconductors |
TDA7073 | Dual BTL power driver | NXP Semiconductors |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |