|
|
PDF TDA7052AT Data sheet ( Hoja de datos )
| Número de pieza | TDA7052AT | |
| Descripción | 1 W BTL mono audio amplifier with DC volume control | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TDA7052AT (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TDA7052A/AT
1 W BTL mono audio amplifier with
DC volume control
Product specification
Supersedes data of August 1991
July 1994
1 page  
NXP Semiconductors
1 W BTL mono audio amplifier with DC
volume control
Product specification
TDA7052A/AT
THERMAL RESISTANCE
SYMBOL
Rth j-a
PARAMETER
from junction to ambient in free air
TDA7052A
TDA7052AT
THERMAL RESISTANCE
100 K/W
155 K/W
Notes to the thermal resistance
TDA7052A: VP = 6 V; RL = 8 Ω. The maximum sine-wave dissipation is 0.9 W.
Therefore Tamb(max) = 150 − 100 × 0.9 = 60 °C.
TDA7052AT: VP = 6 V; RL = 16 Ω. The maximum sine-wave dissipation is 0.46 W.
Therefore Tamb(max) = 150 − 155 × 0.46 = 78 °C.
July 1994
5
5 Page 
NXP Semiconductors
1 W BTL mono audio amplifier with DC
volume control
Product specification
TDA7052A/AT
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
DIP
SOLDERING BY DIPPING OR BY WAVE
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
REPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
WAVE SOLDERING
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
• The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
July 1994
11
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet TDA7052AT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TDA7052A | 1 W BTL mono audio amplifier with DC volume control | NXP Semiconductors |
| TDA7052AT | 1 W BTL mono audio amplifier with DC volume control | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |