DataSheetWiki


TC962MJA fiches techniques PDF

Microchip Technology - High Current Charge Pump DC-to-DC Converter

Numéro de référence TC962MJA
Description High Current Charge Pump DC-to-DC Converter
Fabricant Microchip Technology 
Logo Microchip Technology 





1 Page

No Preview Available !





TC962MJA fiche technique
M
TC962
High Current Charge Pump DC-to-DC Converter
Features
• Pin Compatible With TC7662/ICL7662/SI7661
• High Output Current 80mA
• No External Diodes Required
• Wide Operating Range 3V to 18V
• Low Output Impedance 28Typ.
• No Low Voltage Terminal Required
• Application Zener On-Chip
OSC Frequency Doubling Pin Option for Smaller
Output Capacitors
Applications
Laptop Computers
Disk Drives
Process Instrumentation
µP-Based Controllers
Device Selection Table
Part
Number
TC962COE
TC962CPA
TC962EPA
TC962IJA
TC962MJA
Package
Operating
Temp.
Range
16-Pin SOIC Wide
8-Pin Plastic DIP
8-Pin Plastic DIP
8-Pin CERDIP
8-Pin CERDIP
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-25°C to +85°C
-55°C to +125°C
General Description
The TC962 is an advanced version of the industry
standard TC7662 high voltage DC-to-DC converter.
Using improved design techniques and CMOS
construction, the TC962 can source as much as 80mA
versus the 7662s 20mA capability.
As an inverter, the TC962 can put out voltages as high
as 18V and as low as 3V without the need for external
diodes. The output impedance of the device is a low
28(with the proper capacitors), voltage conversion
efficiency is 99.9%, and power conversion efficiency is
97%.
The low voltage terminal (pin 6) required in some
TC7662 applications has been eliminated. Grounding
this terminal will double the oscillator frequency from
12kHz to 24kHz. This will allow the use of smaller
capacitors for the same output current and ripple, in
most applications. Only two external capacitors are
required for inverter applications. In the event an
external clock is needed to drive the TC962 (such as
paralleling), driving this pin directly will cause the
internal oscillator to sync to the external clock.
Pin 1, which is used as a test pin on the 7662, is a
voltage reference zener on the TC962. This zener
(6.4V at 5mA) has a dynamic impedance of 12and is
intended for use where the TC962 is supplying current
to external regulator circuitry and a reference is needed
for the regulator circuit. (See Section 3.0 Applications
Information).
The TC962 is compatible with the LTC1044, SI7661
and ICL7662. It should be used in designs that require
greater power and/or less input to output voltage drop.
It offers superior performance over the ICL7660S.
Package Type
16-Pin SOIC Wide
Zener
Cathode
C+
GND
C–
8-Pin DIP
8-Pin CERDIP
1• 8
2 TC962CPA 7
TC962EPA
3 TC962IJA 6
4 TC962MJA 5
VDD
COSC
FREQ x 2
VOUT
Zener
Cathode
NC
C+
NC
GND
NC
C
1
2
3
4
5
6
7
TC962COE
16 VDD
15 NC
14 COSC
13 NC
12 FREQ x 2
11 NC
10 VOUT
NC 8
9 NC
2002 Microchip Technology Inc.
DS21484B-page 1

PagesPages 12
Télécharger [ TC962MJA ]


Fiche technique recommandé

No Description détaillée Fabricant
TC962MJA High Current Charge Pump DC-to-DC Converter Microchip Technology
Microchip Technology
TC962MJA HIGH CURRENT CHARGE PUMP DC-TO-DC CONVERTER TelCom Semiconductor
TelCom Semiconductor

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche