ZPSD512B1V-C-20U Datasheet PDF - STMicroelectronics
| Part Number | ZPSD512B1V-C-20U | |
| Description | Low Cost Field Programmable Microcontroller Peripherals | |
| Manufacturers | STMicroelectronics | |
| Logo |  |
|
|
There is a preview and ZPSD512B1V-C-20U download ( pdf file ) link at the bottom of this page. Total 70 Pages | ||
Preview 1 page No Preview Available !
PSD5XX
ZPSD5XX
Low Cost Field Programmable Microcontroller Peripherals
NOT FOR NEW DESIGN
FEATURES SUMMARY
s Single Supply Voltage:
– 5 V±10% for PSD5XX
– 2.7 to 5.5 V for PSD5XX-V
s Up to 1 Mbit of UV EPROM
s Up to 16 Kbit SRAM
s Input Latches
s Programmable I/O ports
s Page Logic
s Programmable Security
Figure 1. Packages
PLDCC68 (J)
CLDCC68 (L)
TQFP68 (U)
January 2002
This is information on a product still in production but not recommended for new designs.
1/3
|
| |
 
PSD5XX Family
Introduction
(cont.)
The Peripheral PLD (PPLD) generates outputs to the Counter/Timer unit and the Interrupt
Controller. The PPLD outputs to the Counter/Timer enable, disable, or trigger counting or
time capture. The PPLD outputs to the Interrupt Controller enables the user to define
conditions for interrupt generation.
The Counter/Timer unit provides four 16-bit highly flexible Counter/Timers. Each has five
modes of operation: pulse, waveform, event counting, time capture, and watchdog
(real-time clock). Each Counter/Timer can be programmed to count up or down. The inputs
to the Counter/Timer, which enable/disable counting or trigger an operation, can originate
from the PPLD directly or directly from the pins. The maximum operating frequency of each
counter is 7.5 MHz. The input clock can be divided (by up to 280) before driving the
Counter/Timer unit using the 4 to 280 prescaler.
The Interrupt Controller has eight levels of priority encoding. It accepts four user-defined
interrupts and four terminal counts from the Counter/Timer. Each interrupt can be
individually masked and configured to be level or edge sensitive. A 3-bit interrupt vector is
generated that can be read by the microcontroller. The serviced interrupt will be cleared
automatically after the microcontroller has read the interrupt vector.
The PSD5XX has 40 I/O pins that are divided among 5 ports. Each I/O pin can be
individually configured to provide many functions, including the following:
• MCU I/O
• ZPLD I/O
• Latched address output (for MCUs with multiplexed data bus)
• Special function I/O (Counter/Timer and Interrupts)
• Data bus (for MCUs with non-multiplexed data bus).
The PSD5XX can easily interface with virtually any 8- or 16-bit microcontroller with a
multiplexed or non-multiplexed bus. All of the MCU control signals are connected to the
ZPLDs, enabling the user to generate signals for external devices. The PSD5XX can
generate a reset output based on the RESET input (includes hysteresis).
The PSD5XX provides between 256 Kbits and 1 Mbit of EPROM that is divided in to four
equal-sized blocks. Each block can occupy a different address location, allowing for
versatile address mapping. The access time of the EPROM includes the address latching
and DPLD decoding.
The PSD5XX has an optional 16 Kbit SRAM that can be battery-backed by connecting a
battery to the Vstby pin. The battery will protect the contents of the SRAM in the event of a
power failure. Therefore, you can place data in the optional SRAM that you want to keep
after the power is switched off. Power switch-over to the battery automatically occurs when
Vcc drops below Vstby.
A four-bit Page Register enables easy access to the I/O section, EPROM, and SRAM for
microcontrollers with limited address space. The Page Register outputs are connected to
the ZPLDs and thus can also be used for external paging schemes.
Please refer to the revision block at
the end of this document for updated
information.
2
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ZPSD512B1V-C-20U electronic component. |
| Information | Total 70 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ ZPSD512B1V-C-20U.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| ZPSD512B1V-C-20J | The function is Low Cost Field Programmable Microcontroller Peripherals. STMicroelectronics | |
| ZPSD512B1V-C-20JI | The function is Low Cost Field Programmable Microcontroller Peripherals. STMicroelectronics | |
| ZPSD512B1V-C-20L | The function is Low Cost Field Programmable Microcontroller Peripherals. STMicroelectronics | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
ZPSD
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||