|
|
Número de pieza | UPD16835 | |
Descripción | MONOLITHIC QUAD H BRIDGE DRIVER CIRCUIT | |
Fabricantes | NEC | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de UPD16835 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! DATA SHEET
MOS INTEGRATED CIRCUIT
µPD16835
MONOLITHIC QUAD H BRIDGE DRIVER CIRCUIT
The µPD16835 is a monolithic quad H bridge driver IC that employs a CMOS control circuit and a MOS FET output
circuit. Because it uses MOS FETs in its output stage, this driver IC consumes less power than conventional driver
ICs that use bipolar transistors.
Because the µPD16835 controls a motor by inputting serial data, its package has been shrunk and the number
of pins reduced. As a result, the performance of the application set can be improved and the size of the set has been
reduced.
This IC employs a current-controlled 64-step micro step driving method that drives stepper motor with low vibration.
The µPD16835 is housed in a 38-pin shrink SOP to contribute to the miniaturization of the application set.
This IC can simultaneously drive two stepper motors and is ideal for the mechanisms of camcorders.
FEATURES
• Four H bridge circuits employing power MOS FETs
• Current-controlled 64-step micro step driving
• Motor control by serial data (8 bytes × 8 bits) (original oscillation: 4-MHz input)
Data is input with the LSB first.
EVR reference setting voltage: 100 to 250 mV (@VREF = 250 mV) ... 4-bit data input (10-mV step)
Chopping frequency: 32 to 124 kHz ... 5-bit data input (4-kHz step)
Original oscillation division or internal oscillation selectable
Number of pulses in 1 VD: 0 to 252 pulses ... 6 bits + 2-bit data input (4 pulses/step)
Step cycle: 0.25 to 8,191.75 µs ... 15-bit data input (0.25-µs step)
• 3-V power supply. Minimum operating voltage: 2.7 V (MIN.)
• Low current consumption IDD: 3 mA (MAX.), IDD (reset): 100 µA (MAX.), IMO: 1 µA (MAX.)
• 38-pin shrink SOP (300 mil)
ABSOLUTE MAXIMUM RATINGS (TA = 25°C)
Parameter
Symbol
Condition
Rating
Supply voltage
VDD
-0.5 to +6.0
VM -0.5 to +11.2
Input voltage
VIN
-0.5 to VDD + 0.5
Reference voltage
VREF
500
H bridge drive currentNote 1
IM (DC)
DC
±150
Instantaneous H bridge drive currentNote 1 IM (pulse)
PW ≤ 10 ms, Duty ≤ 5%
±300
Power consumptionNote 2
PT
1.0
Peak junction temperature
TCH (MAX)
150
Storage temperature
Tstg
-55 to +150
Notes 1. Permissible current per phase with the IC mounted on a PCB.
2. When the IC is mounted on a glass epoxy PCB (10 cm × 10 cm × 1 mm).
The information in this document is subject to change without notice.
Document No. G11594EJ1V0DS00 (1st edition)
Date Published August 1998 J CP(K)
Printed in Japan
Unit
V
V
V
mV
mA/phase
mA/phase
W
°C
°C
© 1998
1 page PIN FUNCTION
No. Name
1 LGND
2 COSC
3 FILA
4 FILB
5 FILC
6 FILD
7 VREF
8 VDD
9 VM3
10 D2
11 FBD
12 D1
13 VM4
14 C2
15 FBC
16 C1
17 EXP0
18 EXP1
19 EXP2
20 PGND
21 EXP3
22 EXTα
23 VM1
24 A1
25 FBA
26 A2
27 VM2
28 B1
29 FBB
30 B2
31 EXTβ
32 VD
33 LATCH
34 SDATA
35 SCLK
36 OSCIN
37 OSCOUT
38 RESET
Function
Control circuit GND pin
Chopping capacitor connection pin
α 1-ch filter capacitor connection pin (1,000 pF TYP.)
α 2-ch filter capacitor connection pin (1,000 pF TYP.)
β 1-ch filter capacitor connection pin (1,000 pF TYP.)
β 2-ch filter capacitor connection pin (1,000 pF TYP.)
Reference voltage input pin (250 mV TYP.)
Control circuit supply voltage input pin
Output circuit supply voltage input pin
β 2-ch output pin
β 2-ch sense resistor connection pin
β 2-ch output pin
Output circuit supply voltage connection pin
β 1-ch output pin
β 1-ch sense resistor connection pin
β 1-ch output pin
Output monitor pin (open-drain)
Output monitor pin (open-drain)
Output monitor pin (open-drain)
Power circuit GND pin
Output monitor pin (open-drain)
Logic circuit monitor pin
Output circuit supply voltage input pin
α 1-ch output pin
α 1-ch sense resistor connection pin
α 1-ch output pin
Output circuit supply voltage input pin
α 2-ch output pin
α 2-ch sense resistor connection pin
α 2-ch output pin
Logic circuit monitor pin
Video sync signal input pin
Latch signal input pin
Serial data input pin
Serial clock input pin
Original oscillation input pin (4 MHz TYP.)
Original oscillation output pin
Reset signal output pin
µPD16835
5
5 Page µPD16835
RELATION BETWEEN ROTATION ANGLE, PHASE CURRENT, AND VECTOR QUANTITY
(64-DIVISION MICRO STEP)
(Values of µPD16835 for reference)
Step
Rotation angle (θ )
A phase current
MIN.
TYP.
MAX.
θ0 0 - 0 -
θ 1 5.6 2.5 9.8 17.0
θ2
11.3
12.4 19.5 26.5
θ3
16.9
22.1 29.1 36.1
θ4
22.5
31.3 38.3 45.3
θ5
28.1
40.1 47.1 54.1
θ6
33.8
48.6 55.6 62.6
θ7
39.4
58.4 63.4 68.4
θ 8 45 65.7 70.7 75.7
θ9
50.6
72.3 77.3 82.3
θ 10
56.3
78.1 83.1 88.1
θ 11
61.9
83.2 88.2 93.2
θ 12
67.5
87.4 92.4 97.4
θ 13
73.1
90.7
95.7 100.7
θ 14
78.8
93.2 98.1 103
θ 15
84.4
- 100 -
θ 16 90 - 100 -
Remark These data do not indicate guaranteed values.
B phase current
MIN.
TYP.
MAX.
- 100 -
- 100 -
93.2
98.1
103
90.7
95.7
100.7
87.4
92.4
97.4
83.2
88.2
93.2
78.1
83.1
88.1
72.3
77.3
82.3
65.7
70.7
75.7
58.4
63.4
68.4
48.6
55.6
62.6
40.1
47.1
54.1
31.3
38.3
45.3
22.1
29.1
36.1
12.4
19.5
26.5
2.5 9.8 17.0
-0 -
Vector quantity
TYP.
100
100.48
100
100.02
100.02
99.99
99.98
99.97
99.98
99.97
99.98
99.99
100.02
100.02
100
100.48
100
11
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet UPD16835.PDF ] |
Número de pieza | Descripción | Fabricantes |
UPD168302 | MONOLITHIC 2CH H-BRIDGE DRIVER | NEC |
UPD16833A | MONOLITHIC QUAD H BRIDGE DRIVER CIRCUIT | NEC |
UPD16833AG3 | MONOLITHIC QUAD H BRIDGE DRIVER CIRCUIT | NEC |
UPD16835 | MONOLITHIC QUAD H BRIDGE DRIVER CIRCUIT | NEC |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |