DataSheetWiki


PCA9517 fiches techniques PDF

NXP Semiconductors - Level translating I2C-bus repeater

Numéro de référence PCA9517
Description Level translating I2C-bus repeater
Fabricant NXP Semiconductors 
Logo NXP Semiconductors 





1 Page

No Preview Available !





PCA9517 fiche technique
PCA9517
Level translating I2C-bus repeater
Rev. 03 — 30 January 2007
Product data sheet
1. General description
The PCA9517 is a CMOS integrated circuit that provides level shifting between low
voltage (down to 0.9 V) and higher voltage (2.7 V to 5.5 V) I2C-bus or SMBus applications.
While retaining all the operating modes and features of the I2C-bus system during the
level shifts, it also permits extension of the I2C-bus by providing bidirectional buffering for
both the data (SDA) and the clock (SCL) lines, thus enabling two buses of 400 pF. Using
the PCA9517 enables the system designer to isolate two halves of a bus for both voltage
and capacitance. The SDA and SCL pins are over voltage tolerant and are
high-impedance when the PCA9517 is unpowered.
The 2.7 V to 5.5 V bus B-side drivers behave much like the drivers on the PCA9515A
device, while the adjustable voltage bus A-side drivers drive more current and eliminate
the static offset voltage. This results in a LOW on the B-side translating into a nearly 0 V
LOW on the A-side which accommodates smaller voltage swings of lower voltage logic.
The static offset design of the B-side PCA9517 I/O drivers prevent them from being
connected to another device that has rise time accelerator including the PCA9510,
PCA9511, PCA9512, PCA9513, PCA9514, PCA9515A, PCA9516A, PCA9517 (B-side),
or PCA9518. The A-side of two or more PCA9517s can be connected together, however,
to allow a star topography with the A-side on the common bus, and the A-side can be
connected directly to any other buffer with static or dynamic offset voltage. Multiple
PCA9517s can be connected in series, A-side to B-side, with no build-up in offset voltage
with only time of flight delays to consider.
The PCA9517 drivers are not enabled unless VCCA is above 0.8 V and VCC is above 2.5 V.
The EN pin can also be used to turn the drivers on and off under system control. Caution
should be observed to only change the state of the enable pin when the bus is idle.
The output pull-down on the B-side internal buffer LOW is set for approximately 0.5 V,
while the input threshold of the internal buffer is set about 70 mV lower (0.43 V). When the
B-side I/O is driven LOW internally, the LOW is not recognized as a LOW by the input.
This prevents a lock-up condition from occurring. The output pull-down on the A-side
drives a hard LOW and the input level is set at 0.3VCCA to accommodate the need for a
lower LOW level in systems where the low voltage side supply voltage is as low as 0.9 V.
2. Features
I 2 channel, bidirectional buffer isolates capacitance and allows 400 pF on either side of
the device
I Voltage level translation from 0.9 V to 5.5 V and from 2.7 V to 5.5 V
I Footprint and functional replacement for PCA9515/15A
I I2C-bus and SMBus compatible

PagesPages 19
Télécharger [ PCA9517 ]


Fiche technique recommandé

No Description détaillée Fabricant
PCA9510 Hot swappable I2C and SMBus bus buffer NXP Semiconductors
NXP Semiconductors
PCA9510A Hot swappable I2C-bus and SMBus bus buffer NXP Semiconductors
NXP Semiconductors
PCA9510D Hot swappable I2C and SMBus bus buffer NXP Semiconductors
NXP Semiconductors
PCA9510DP Hot swappable I2C and SMBus bus buffer NXP Semiconductors
NXP Semiconductors

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche