|
|
PDF TDA8354Q Data sheet ( Hoja de datos )
| Número de pieza | TDA8354Q | |
| Descripción | Full bridge current driven vertical deflection output circuit in LVDMOS | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TDA8354Q (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TDA8354Q
Full bridge current driven vertical
deflection output circuit in LVDMOS
Preliminary specification
File under Integrated Circuits, IC02
1998 Sep 03
1 page  
Philips Semiconductors
Full bridge current driven vertical deflection
output circuit in LVDMOS
Preliminary specification
TDA8354Q
Guard circuit
A guard circuit with output signal Vo(guard) is provided.
The guard circuit generates an active HIGH level during
the flyback period. The guard circuit is also activated for
one or more of the following conditions:
• When the thermal protection is activated (Tj ≈ 170 °C)
• During short-circuit of the output pins (pins 5 and 9) to
VP or ground
• During open coil
• During open loop
• During short-circuit of the input pins (pins 11 and 12) to
VP or ground.
An active HIGH level of the guard signal is also generated
for the next conditions:
• No drive signal
• Short-circuit of the coil.
However, for these events the signal is generated via an
internal timer circuit. The guard signal set via this timer has
a delay of ≈120 ms. The delay time is given by the lowest
applicable field frequency.
The guard signal can be used for blanking the picture tube
screen and signalling a fault condition.
Damping resistor compensation
For HF-loop stability a damping resistor is connected
across the deflection coil. There is a big difference in
current in the damping resistor Rp during scan and flyback.
The resistor current is summed to the current in the
deflection coil via the measuring resistor RM, which results
in a too low current in the deflection coil at the start of the
scan.
To reach a short settling time the difference in the current
during scan and flyback in the damping resistor can be
compensated for by external means. To do so a resistor
(Rcomp) of about 1 MΩ can be connected between the
output of stage A (pin 9) and the damping resistor
compensation current input (pin 13).
For a more accurate calculation of Rcomp refer to the
following formula:
Rcomp = --(--V-(---Vf--l-b-f-l--b–----–-V---V-l-o---ls-o--s-s--s-–---–-V----IP--L--)--×--×--R---R--L---p)----××----R-R----c-M--o--n-
1998 Sep 03
5
5 Page 
Philips Semiconductors
Full bridge current driven vertical deflection
output circuit in LVDMOS
TEST AND APPLICATION INFORMATION
Preliminary specification
TDA8354Q
handbook, full pagewidth
R(guard)
Vo(guard)
1
VP(B)
4
VP(A)
10
Vflb
7
VP
Vflb
C3 C4
Ii(diff)
Ii(bias)
Ii(diff)
GUARD
CIRCUIT
Ii(bias)
Ii(pos) 12
9 Vo(A)
RL
Ii(diff)
Ii(diff)
INPUT/
FEEDBACK
Ii(diff)
Ii(bias)
Ii(diff)
Ii(bias)
11
Ii(neg)
Rcomp Rp coil
COMPENSATION 13 Ii(comp)
CIRCUIT
2 Vi(M)
Rs
3 Vi(con)
Rcon
RM
5 Vo(B)
TDA8354Q
68
GNDB GNDA
MGL463
Fig.3 Test diagram.
1998 Sep 03
11
11 Page | ||
| Páginas | Total 16 Páginas | |
| PDF Descargar | [ Datasheet TDA8354Q.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TDA8354 | Full bridge current driven vertical deflection output circuit in LVDMOS | NXP Semiconductors |
| TDA8354Q | Full bridge current driven vertical deflection output circuit in LVDMOS | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |