|
|
Número de pieza | E713704 | |
Descripción | 16-bit Proprietary Microcontroller | |
Fabricantes | Fujitsu Media Devices Limited | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de E713704 (archivo pdf) en la parte inferior de esta página. Total 56 Páginas | ||
No Preview Available ! FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-13704-5E
16-bit Proprietary Microcontroller
CMOS
F2MC-16LX MB90590/590G Series
MB90591/591G/F591A/F591G/594/594G/F594A/F594G
MB90V590A/V590G
s DESCRIPTION
The MB90590/590G series with two FULL-CAN*1 interfaces and FLASH ROM is especially designed for automo-
tive and industrial applications. Its main features are two on board CAN Interfaces, which conform to V2.0 Part A
and Part B, while supporting a very flexible message buffer scheme and so offering more functions than a normal
full CAN approach.
The instruction set of F2MC-16LX CPU core inherits an AT architecture of the F2MC*2 family with additional
instruction sets for high-level languages, extended addressing mode, enhanced multiplication/division instructions,
and enhanced bit manipulation instructions. The microcontroller has a 32-bit accumulator for processing long
word data.
The MB90590/590G series has peripheral resources of 8/10-bit A/D converters, UART (SCI), extended I/O serial
interface, 8/16-bit PPG timer, I/O timer (input capture (ICU), output compare (OCU)), stepping motor controller,
and sound generator.
*1 : Controller Area Network (CAN) - License of Robert Bosch GmbH
*2 : F2MC stands for FUJITSU Flexible Microcontroller.
s PACKAGE
100-pin Plastic QFP
(FPT-100P-M06)
1 page MB90590/590G Series
(Continued)
Features
MB90591/591G/594/594G
MB90F591A/F591G/
F594A/F594G
MB90V590A/V590G
CAN Interface
Number of channels : 2
Conforms to CAN Specification Version 2.0 Part A and B
Automatic re-transmission in case of error
Automatic transmission responding to Remote Frame
Prioritized 16 message buffers for data and ID’s
Supports multiple messages
Flexible configuration of acceptance filtering :
Full bit compare / Full bit mask / Two partial bit masks
Supports up to 1Mbps
CAN bit timing setting :
MB90xxx : TSEG2 ≥ RSJW+2TQ
MB90xxxG : TSEG2 ≥ RSJW
Stepping motor controller Four high current outputs for each channel
(4 channels)
Synchronized two 8-bit PWM’s for each channel
External interrupt circuit
Number of inputs : 8
Started by a rising edge, a falling edge, an “H” level input, or an “L” level input.
Sound generator
8-bit PWM signal is mixed with tone frequency from 8-bit reload counter
PWM frequency : 62.5K, 31.2K, 15.6K, 7.8KHz (at System clock = 16MHz)
Tone frequency : PWM frequency / 2 / (reload value + 1)
Extended I/O serial
interface
Clock synchronized transmission (31.25K/62.5K/125K/500K/1Mbps at machine clock
frequency of 16 MHz)
LSB first/MSB first
Clock timer
Directly operates with the system clock
Read/Write accessible Second/Minute/Hour registers
Watchdog timer
Reset generation interval : 3.58 ms, 14.33 ms, 57.23 ms, 458.75 ms
(at oscillation of 4 MHz, minimum value)
Flash Memory
Supports automatic programming, Embedded Algorithm TM and
Write/Erase/Erase-Suspend/Resume commands
A flag indicating completion of the algorithm
Hard-wired reset vector available in order to point to a fixed boot sector in Flash
Memory
Boot block configuration
Erase can be performed on each block
Block protection with external programming voltage
Flash Writer from Minato Electronics Inc.
Low-power consumption
(stand-by) mode
Sleep/stop/CPU intermittent operation/clock timer/hardware stand-by
Process
CMOS
Power supply voltage for
operation*2
5 V±10 % (MB90V590A, MB90F594A, MB90594, MB90V590G,
MB90F594G, MB90594G)
5 V±5 % (MB90F591G, MB90591G, MB90F591A, MB90591)
Package
QFP-100
PGA-256
*1 : It is setting of DIP switch S2 when Emulation pod (MB2145-507) is used.
Please refer to the MB2145-507 hardware manual (2.7 Emulator-specific Power Pin) about details.
*2 : Varies with conditions such as the operating frequency. (See section “s Electrical Characteristics.”)
5
5 Page s I/O CIRCUIT TYPE
Circuit Type
X1
Circuit
X0
A
MB90590/590G Series
Remarks
• Oscillation feedback resistor :
Clock
Input
1 MΩ approx.
HARD,SOFT
STANDBY
CONTROL
• Hysteresis input with pull-up resistor :
50 kΩ approx.
B R (pull-up)
R HYS
• Hysteresis input
C R HYS
VCC
P-ch
• CMOS output
• Hysteresis input
D N-ch
R HYS
(Continued)
11
11 Page |
Páginas | Total 56 Páginas | |
PDF Descargar | [ Datasheet E713704.PDF ] |
Número de pieza | Descripción | Fabricantes |
E713704 | 16-bit Proprietary Microcontroller | Fujitsu Media Devices Limited |
E713704 | 16-bit Proprietary Microcontroller | Fujitsu Media Devices Limited |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |