SAB83C166-M Datasheet PDF - Siemens Semiconductor Group
| Part Number | SAB83C166-M | |
| Description | 16-Bit CMOS Single-Chip Microcontroller | |
| Manufacturers | Siemens Semiconductor Group | |
| Logo |  |
|
|
There is a preview and SAB83C166-M download ( pdf file ) link at the bottom of this page. Total 52 Pages | ||
Preview 1 page No Preview Available !
Microcomputer Components
16-Bit CMOS Single-Chip Microcontroller
SAB 80C166/83C166
Data Sheet 09.94
|
| |
 
SAB 80C166/83C166
Pin Definitions and Functions
Symbol
P4.0 –
P4.1
Pin Input
Number Output
16-17 I/O
XTAL1
XTAL2
16
17
20
19
O
O
I
O
BUSACT, 22
EBC1, 23
EBC0
24
I
I
I
RSTIN 27
I
RSTOUT 28
O
Function
Port 4 is a 2-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-impedance
state.
In case of an external bus configuration, Port 4 can be used to
output the segment address lines:
P4.0
A16 Least Significant Segment Addr. Line
P4.1
A17 Most Significant Segment Addr. Line
XTAL1: Input to the oscillator amplifier and input to the
internal clock generator
XTAL2: Output of the oscillator amplifier circuit.
To clock the device from an external source, drive XTAL1, while
leaving XTAL2 unconnected. Minimum and maximum high/low
and rise/fall times specified in the AC Characteristics must be
observed.
External Bus Configuration selection inputs. These pins are
sampled during reset and select either the single chip mode or
one of the four external bus configurations:
BUSACT EBC1 EBC0 Mode/Bus Configuration
0 0 0 8-bit demultiplexed bus
0 0 1 8-bit multiplexed bus
0 1 0 16-bit multiplexed bus
0 1 1 16-bit demultiplexed bus
1 0 0 Single chip mode
1 0 1 Reserved.
1 1 0 Reserved.
1 1 1 Reserved.
ROMless versions must have pin BUSACT tied to ‘0’.
Reset Input with Schmitt-Trigger characteristics. A low level at
this pin for a specified duration while the oscillator is running
resets the SAB 80C166. An internal pullup resistor permits
power-on reset using only a capacitor connected to VSS.
Internal Reset Indication Output. This pin is set to a low level
when the part is executing either a hardware-, a software- or a
watchdog timer reset. RSTOUT remains low until the EINIT
(end of initialization) instruction is executed.
Semiconductor Group
4
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for SAB83C166-M electronic component. |
| Information | Total 52 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ SAB83C166-M.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| SAB83C166-5M | The function is 16-Bit CMOS Single-Chip Microcontroller. Infineon Technologies AG |  |
| SAB83C166-5M-T3 | The function is 16-Bit CMOS Single-Chip Microcontroller. Infineon Technologies AG | |
| SAB83C166-M | The function is 16-Bit CMOS Single-Chip Microcontroller. Siemens Semiconductor Group | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
SAB8
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||