DataSheetWiki


SCAN18373T fiches techniques PDF

National Semiconductor - Transparent Latch with TRI-STATE Outputs

Numéro de référence SCAN18373T
Description Transparent Latch with TRI-STATE Outputs
Fabricant National Semiconductor 
Logo National Semiconductor 





1 Page

No Preview Available !





SCAN18373T fiche technique
September 1998
SCAN18373T
Transparent Latch with TRI-STATE® Outputs
General Description
The SCAN18373T is a high speed, low-power transparent
latch featuring separate data inputs organized into dual 9-bit
bytes with byte-oriented latch enable and output enable con-
trol signals. This device is compliant with IEEE 1149.1 Stan-
dard Test Access Port and Boundary Scan Architecture with
the incorporation of the defined boundary-scan test logic and
test access port consisting of Test Data Input (TDI), Test
Data Out (TDO), Test Mode Select (TMS), and Test Clock
(TCK).
Features
n IEEE 1149.1 (JTAG) Compliant
n Buffered active-low latch enable
n TRI-STATE outputs for bus-oriented applications
n 9-bit data busses for parity applications
n Reduced-swing outputs source 24 mA/sink 48 mA
n Guaranteed to drive 50transmission line to TTL input
levels of 0.8V and 2.0V
n TTL compatible inputs
n 25 mil pitch Cerpack packaging
n Includes CLAMP and HIGHZ instructions
n Standard Microcircuit Drawing (SMD) 5962-9311801
Connection Diagram
DS100321-1
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 1998 National Semiconductor Corporation DS100321
Pin Names
AI(0–8), BI(0–8)
ALE, BLE
AOE1, BOE1
AO(0–8), BO(0–8)
Description
Data Inputs
Latch Enable Inputs
TRI-STATE Output Enable Inputs
TRI-STATE Latch Outputs
Truth Tables
ALE
X
H
H
L
Inputs
AOE1
H
L
L
L
AI (0–8)
X
L
H
X
Inputs
BLE
X
BOE1
H
BI (0–8)
X
HL
L
HL
H
LL
X
H= HIGH Voltage Level
L= LOW Voltage Level
X= Immaterial
Z= High Impedance
AO0 = Previous AO before H-to-L transition of ALE
BO0 = Previous BO before H-to-L transition of BLE
AO (0–8)
Z
L
H
AO0
BO (0–8)
Z
L
H
BO0
Functional Description
The SCAN18373T consists of two sets of nine D-type
latches with TRI-STATE standard outputs. When the Latch
Enable (ALE or BLE) input is HIGH, data on the inputs
(AI(0–8) or BI(0–8) ) enters the latches. In this condition the
latches are transparent, i.e., a latch output will change state
each time its input changes. When Latch Enable is LOW, the
latches store the information that was present on the inputs
a set-up time preceding the HIGH-to-LOW transition of the
www.national.com

PagesPages 14
Télécharger [ SCAN18373T ]


Fiche technique recommandé

No Description détaillée Fabricant
SCAN18373T Transparent Latch with TRI-STATE Outputs National Semiconductor
National Semiconductor
SCAN18373T SCAN18373T Transparent Latch with TRI-STATE Outputs (Rev. B) Texas Instruments
Texas Instruments

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche