DataSheetWiki


OPB963T11 fiches techniques PDF

Optek Technology - Photolohic Slotted Optical Switches

Numéro de référence OPB963T11
Description Photolohic Slotted Optical Switches
Fabricant Optek Technology 
Logo Optek Technology 





1 Page

No Preview Available !





OPB963T11 fiche technique
Product Bulletin OPB960
February 1998
PhotologicSlotted Optical Switches
Types OPB960, OPB970 Series
Features
Choice of mounting configuration
Choice of aperture
Choice of output configuration
Choice of opaque or IR transmissive
shell material
Data rates to 250 kBaud
0.320”lead spacing for PC board
mount
Description
The OPB960 and OPB970 series of
PhotologicPhoto Integrated Circuit
Switches provide optimum flexibility for
the design engineer. Buidling from a
standard housing with a .125”wide slot,
the user can specify (1) type and polarity
of TTL output, (2) discrete shell material,
(3) aperture width, and (4) type of
mounting configuration. Available with
24”, 26AWG wire leads as
OPB980/OPB990 series.
The electrical ouput can be specified as
either ttL totem pole or TTL open
collector. Either may be supplied with
inverter or buffer output polarity. All have
added stability of a built-in hysteresis
amplifier.
Absolute Maximum Ratings (TA = 25oC unless otherwise noted)
Supply Voltage, VCC (Not to exceed 3 sec.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +85oC
Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to +70oC
Lead Soldering Temperature [1/16 inch (1.6mm) from case for 5 sec. with soldering
iron] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240oC(1)
Input Diode Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mW(2)
Output PhotologicPower Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200mW(3)
Total Device Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300mW(4)
Voltage at Output Lead (Open Collector Output) . . . . . . . . . . . . . . . . . . . . . . . . . . 35V
Diode Forward D.C. Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40mA
Diode Reverse D.C. Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2V
Notes:
(1) RMA flux is recommended. Duration can be extended to 10 sec. max. when flow soldering.
(2) Derate linearly 2.22mW/oC above 25o C.
(3) Derate linearly 4.44mW/oC above 25o C.
(4) Derate linearly 6.66mW/oC above 25o C.
(5) The OPB960/OPB970 series are terminated with .020" square leads designed for printed
circuit board mounting.
(6) Normal application would be with light source blocked, simulated by IF = 0mA.
(7) All parameters tested using pulse technique.
Housing
All housings are an opaque grade of injection-molded plastic to minimize the
assembly’s sensitivity to ambient radiation, both visible and near-infrared. Discrete
shells (exposed on the parallel faces inside the device throat) are either IR
transmissive plastic for applications where aperture contamination may occur or
opaque plastic for maximum protection against ambient light.
Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible.
1-OTWO

PagesPages 4
Télécharger [ OPB963T11 ]


Fiche technique recommandé

No Description détaillée Fabricant
OPB963T11 Photolohic Slotted Optical Switches Optek Technology
Optek Technology

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche