DataSheetWiki


K9F5608U0M-YIB0 fiches techniques PDF

Samsung semiconductor - 32M x 8 Bit NAND Flash Memory

Numéro de référence K9F5608U0M-YIB0
Description 32M x 8 Bit NAND Flash Memory
Fabricant Samsung semiconductor 
Logo Samsung semiconductor 





1 Page

No Preview Available !





K9F5608U0M-YIB0 fiche technique
K9F5608U0M-YCB0,K9F5608U0M-YIB0
Document Title
32M x 8 Bit NAND Flash Memory
FLASH MEMORY
Revision History
Revision No. History
0.0 Initial issue.
Draft Date
April. 10th 1999
0.1 Revised real-time map-out algorithm(refer to technical notes)
July. 23th 1999
0.2 1. Changed device name
i. KM29U256T -> K9F5608U0M-YCB0
ii. KM29U256IT -> K9F5608U0M-YIB0
Sep. 15th 1999
0.3 1. Changed tWP AC Timing
Mar. 21th 2000
- If tCS is set less than 10ns, tWP must be minimum 35ns, otherwise
tWP may be minimum 25ns.
2. Changed Sequential Row Read operation
- The Sequential Read 1 and 2 operation is allowed only within a block
3. Changed invalid block(s) marking method prior to shipping
- The invalid block(s) information is written the 1st or 2nd page of the
invalid block(s) with 00h data
--->The invalid block(s) status is defined by the 6th byte in the spare
area. Samsung makes sure that either the 1st or 2nd page of every
invalid block has 00h data at the column address of 517.
4. Added a new card-type package : K9S5608U0M-MCB0
0.4 1. Changed Endurance : 1million -> 100K Program/Erase Cycles
Apr. 7th 2000
0.5 1. Changed package name
Apr. 29th 2000
: K9S5608U0M-MCB0 ->K9F5608U0M-MCB0(Micro Flash Card)
2. Changed invalid block(s) marking method prior to shipping
- The invalid block(s) status is defined by the 6th byte in the spare
area. Samsung makes sure that either the 1st or 2nd page of every
invalid block has 00h data at the column address of 517.
--->The invalid block(s) status is defined by the 6th byte in the spare
area. Samsung makes sure that either the 1st or 2nd page of every
invalid block has non-FFh data at the column address of 517.
0.6 1. Removed Micro Flash Card
July 17th 2000
2. Changed SE pin description
- SE is recommended to coupled to GND or Vcc and should not be
toggled during reading or programming.
0.7 1. Explain how pointer operation works in detail.
Nov. 20th 2000
2. Renamed GND input (pin # 6) on behalf of SE (pin # 6)
- The SE input controls the access of the spare area. When SE is high,
the spare area is not accessible for reading or programming. SE is rec
ommended to be coupled to GND or Vcc and should not be toggled
during reading or programming.
=> Connect this input pin to GND or set to static low state unless the
sequential read mode excluding spare area is used.
3. Updated operation for tRST timing
- If reset command(FFh) is written at Ready state, the device goes into
Busy for maximum 5us.
Remark
Advanced
Information
Advanced
Information
Preliminary
Preliminary
Preliminary
Preliminary
Final
The attached datasheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right
to change the specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions about device. If you have
any questions, please contact the SAMSUNG branch office near you.
1

PagesPages 26
Télécharger [ K9F5608U0M-YIB0 ]


Fiche technique recommandé

No Description détaillée Fabricant
K9F5608U0M-YIB0 32M x 8 Bit NAND Flash Memory Samsung semiconductor
Samsung semiconductor

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche