|
|
PDF ILX526A Data sheet ( Hoja de datos )
| Número de pieza | ILX526A | |
| Descripción | 3000-pixel CCD Linear Image Sensor (B/W) | |
| Fabricantes | Sony Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ILX526A (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
ILX526A
3000-pixel CCD Linear Image Sensor (B/W)
Description
The ILX526A is a rectangular reduction type CCD
linear image sensor designed for bar code POS
hand scanner and optical measuring equipment use.
A built-in timing generator and clock-drivers ensure
single 5V power supply for easy use.
22 pin DIP (Cer-DIP)
Features
• Number of effective pixels: 3000 pixels
• Pixel size: 7µm × 200µm (7µm pitch)
• Single 5V power supply
• High sensitivity: 300V/(lx · s)
• Built-in timing generator and clock-drivers
• Built-in sample-and-hold circuit
• Electrical shutter function
• Clock frequency: 100kHz (Min), 1MHz (Max)
Internal Structure
Absolute Maximum Ratings
• Supply voltage
VDD
• Operating temperature
• Storage temperature
6
–10 to +60
–30 to +80
V
°C
°C
Pin Configuration (Top View)
Vgg 1
φCLK 2
NC 3
NC 4
NC 5
φROG 6
φSHUT 7
GND 8
VDD 9
T1 10
NC 11
1
3000
22 VDD
21 GND
20 VOUT
19 NC
18 NC
17 NC
16 NC
15 NC
14 VDD
13 GND
12 S/HSW
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E97803-PS
1 page  
ILX526A
–5–
5 Page 
ILX526A
Notes of Handling
1) Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling be sure to take the following
protective measures.
a) Either handle bare handed or use non chargeable gloves, clothes or material.
Also use conductive shoes.
b) When handling directly use an earth band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) Ionized air is recommended for discharge when handling CCD image sensor.
e) For the shipment of mounted substrates, use boxes treated for prevention of static charges.
2) Notes on Handling CCD Cer-DIP Packages
The following points should be observed when handling and installing cer-DIP packages.
a) Remain within the following limits when applying static load to the ceramic portion of the package:
(1) Compressive strength: 39N/surface (Do not apply load more than 0.7mm inside the outer perimeter of
the glass portion.)
(2) Shearing strength: 29N/surface
(3) Tensile strength: 29N/surface
(4) Torsional strength: 0.9Nm
Upper ceramic layer 39N
29N
29N
0.9Nm
Low-melting glass
Lower ceramic layer (1)
(2)
(3)
(4)
b) In addition, if a load is applied to the entire surface by a hard component, bending stress may be
generated and the package may fracture, etc., depending on the flatness of the ceramic portion.
Therefore, for installation, either use an elastic load, such as a spring plate, or an adhesive.
c) Be aware that any of the following can cause the glass to crack: because the upper and lower ceramic
layers are shielded by low-melting glass,
(1) Applying repetitive bending stress to the external leads.
(2) Applying heat to the external leads for an extended period of time with soldering iron.
(3) Rapid cooling or heating.
(4) Applying a load or impact to a limited portion of the low-melting glass with a small-tipped tool such as
tweezers.
(5) Prying the upper or lower ceramic layers away at a support point of the low-melting glass.
Note that the preceding notes should also be observed when removing a component from a board after it
has already been soldered.
3) Soldering
a) Make sure the package temperature does not exceed 80°C.
b) Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a grounded 30W
soldering iron and solder each pin in less then 2 seconds. For repairs and remount, cool sufficiently.
c) To dismount an imaging device, do not use a solder suction equipment. When using an electric
desoldering tool, ground the controller. For the control system, use a zero cross type.
– 11 –
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet ILX526A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ILX526A | 3000-pixel CCD Linear Image Sensor (B/W) | Sony Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |