DataSheetWiki


EL6287C fiches techniques PDF

Elantec Semiconductor - 4-Ch Laser Diode Driver + Oscillator

Numéro de référence EL6287C
Description 4-Ch Laser Diode Driver + Oscillator
Fabricant Elantec Semiconductor 
Logo Elantec Semiconductor 





1 Page

No Preview Available !





EL6287C fiche technique
EL6287C - Product Brief
4-Ch Laser Diode Driver + Oscillator
Features
• “Shrink-Small” Outline Package
• Voltage-controlled output current
source requiring one external set
resistor per channel
• Current-controlled output current
source
• Rise time = 0.8 nsec
• Fall time = 0.8 nsec
• On chip oscillator with frequency
and amplitude control by use of
external resistors to ground
• Oscillator to 500MHz
• Oscillator to 100mA pk/pk
• Single +5V supply (±10%)
• Disable feature for power-up
protection and power savings
• CMOS control signals
Applications
• CD-RW applications
• Writable optical drives
• Laser diode current switching
Ordering Information
Part No
EL6287CU
Temp. Range
0°C to +70°C
Package
24-Pin QSOP
Outline #
MDP0040
General Description
The EL6287C is a four channel laser diode current amplifier that pro-
vides controlled current to a grounded laser diode. Channels 2, 3, and
4 must be used as the write channels, with switching speeds of approx-
imately one nanosecond rise/fall time. All four channels are summed
together at the IOUT output, allowing the user to create multilevel
waveforms in order to optimize laser diode performance. The level of
the output current is set by an analog voltage applied to an external
resistor which converts the voltage into a current at the IIN pin (virtu-
ally ground). The current seen at this pin is then amplified to become a
current source at pin IOUT.
An on-chip 500MHz oscillator is provided to allow current modula-
tion when in read mode. This is turned on when the OSCEN pin is held
high. Complete control of amplitude and frequency is set by two exter-
nal resistors connected to ground at pins RFREQ and RAMP (see
graphs in this data sheet for further explanation). The oscillator will
turn off whenever any of the OUTEN pins for channels 2, 3, or 4 (the
write channels) are low (see truth table).
The external resistors allow the user to accurately and independently
set each amplifier transconductance by applying a voltage to each
resistor, without restriction on the voltage range, thus ensuring broad
voltage DAC compatibility. Alternatively, the IIN pin can be biased
from a current DAC or other current source.
Connection Diagram
1 GND
GND 24
2 IINR
VCC 23
3 GND
VCC 22
4 IIN2
IOUT 21
5 RFREQ
IOUT 20
6 IIN3
GND 19
7 IIN4
RAMP 18
8 OUTENR ENABLE 17
9 OUTEN2 OSCEN 16
10 OUTEN3 VCC 15
11 OUTEN4 VCC 14
12 GND
GND 13
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.

PagesPages 2
Télécharger [ EL6287C ]


Fiche technique recommandé

No Description détaillée Fabricant
EL6287C 4-Ch Laser Diode Driver + Oscillator Elantec Semiconductor
Elantec Semiconductor
EL6287CU 4-Ch Laser Diode Driver + Oscillator Elantec Semiconductor
Elantec Semiconductor

US18650VTC5A

Lithium-Ion Battery

Sony
Sony
TSPC106

PCI Bus Bridge Memory Controller

ATMEL
ATMEL
TP9380

NPN SILICON RF POWER TRANSISTOR

Advanced Semiconductor
Advanced Semiconductor


www.DataSheetWiki.com    |   2020   |   Contactez-nous  |   Recherche